Versions Compared

Version Old Version 5 New Version 6
Changes made by

Sebastian Florek-Paszkowski (Unlicensed)

Sebastian Florek-Paszkowski (Unlicensed)

Saved on

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.

Initial Use

  1. Before inserting TITAN into the gearboxAfter unboxing and before installation, connect TITAN to GCS via Blu-Link or USB-Link. You can download GCS here: https://www.gatee.eu/gcs

    Image RemovedImage Added

    Image Added


    The GCS Information for Use is here: https://www.gatee.eu/manuals

    Image RemovedImage Added

  2. Check for latest firmware updates.

Info

Note
Your Android (version 5.0 or higher) device must support OTG technology to run the GATE Control Station App.

Info

Note 
You need a USB-Link or a Blu-Link to connect your TITAN to the GATE Control Station for Android and Windows/macOS. To connect to the iOS GCS, you must use a Blu-Link.

Now you’re ready to install TITAN in the gearbox.

...

Info

Caution
In TITAN V2 connectors must be bent according to the photo below. Bending connectors in the opposite direction may cause them to break them. If this should happen, spare terminals are included in the installation kit.

...

Info

Note
Use the trigger sticker to make it visible for the trigger sensor.

*grafika*

Info

Note
TITAN can detect trigger position very precisely. In order to use it, you need to eliminate trigger backlash. The set contains 3 trigger anti-backlash stickers of various thicknesses. Try each one of them and choose the most appropriate one.

*grafika*Image Added
Info

Note
The selector plate requires modification. Place the selector sticker according to the photos below. Its position is crucial.

*grafika łącząca dwie dotychczasowe*Image Added
Info

Caution

In TITAN V3 the connectors

should

must be straight according to the photo below. Bending and straightening the connectors back may cause them to break. If this happens, spare terminals are included in the installation kit.

...

Image Added

TITAN V2 NGRS

Note

Warning
If you are using a recoil system and set excessive trigger sensitivity, it may cause incidental discharge (firing) even without pressing the trigger.

Note

Warning
If you are using a recoil system and set excessive trigger sensitivity, it may cause accidental discharge even without pressing the trigger.

...

...

Note

Warning
Pay attention to correctly solder positive and negative TITAN wires to the connector. Incorrectly connecting positive and negative battery terminals will cause immediate damage to the device, which is not covered by warranty, and can lead to fire.  

...

Caution
An insulation washer is required. Placing washers in the wrong order

...

will cause a short circuit and permanent damage to TITAN, which is not covered by warranty.

...

Caution
Do not locate the screw in the cut-off lever hole to secure the TITAN board. Use a contact block mounting screw in the hole indicated by the arrow.

...

Caution
Incorrect placement of wiring under the motor gear may cause insulation damage and a short circuit, which is not covered by warranty.*grafika*

...

Caution
In order to secure the wires properly, modify the gearbox as shown in the photos below.

...

...

Info

Note
The selector plate requires modification. Place the selector sticker according to the photos below. Its position is crucial.

...

Caution
In TITAN NGRS connectors should be bent according to the photo below. Bending connectors in the opposite direction may cause them to break. If this happens, spare terminals are included in the installation kit.

...

Quick Access

...

Menu

Instructions

 

...

Powiązane artykuły

Filter by label (Content by label)
showLabelsfalse
max5
spacescom.atlassian.confluence.content.render.xhtml.model.resource.identifiers.SpaceResourceIdentifier@a32
sortmodified
showSpacefalse
reversetrue
typepage
cqllabel = "kb-how-to-article" and type = "page" and space = "RD"
labelskb-how-to-article

...

hiddentrue

...

You can access Pre-cocking or Profiles using a shortcut. After firing a shot, burst or while in SAFE (only if the safety lever has been removed)*, hold the trigger and switch the fire selector within the specified time (see table). Switch the fire selector in any order to change between options indicated by motor vibrations. 

By releasing the trigger, you exit the function confirming it. Bear in mind that programming via trigger is a different process. To find out more check the PROGRAMMING VIA TRIGGER CARD included or https://gatee.eu/technical-support/manuals.

...

*You can enter Programming via Trigger only when the Fire Selector on the replica is in SEMI position and AUTO mode is not assigned to this position.

Function

available if preset in GCS

in SEMI or BURST mode preset in GCS in SEMI physical position only

Pre-cocking

Profiles (EXPERT only)

Programming via trigger

To enter the function: hold the trigger 

and switch the Fire Selector within 2 s

and switch the Fire Selector within 2–7 s

for > 7 s 

Available options

Option

Low frequency vibration

Option

High frequency vibration

check the PROGRAMMING VIA TRIGGER CARD included or https://gatee.eu/technical-support/manuals

Off

1

Profile 1

1

Auto

2

Profile 2

2

Manual*

3

Profile 3

3

Pre-cocking Selection

In GCS go to Trigger>Pre-cocking>Switch mode via Fire Selector and use the toggle button to activate this function.

  1. Fire a shot, burst or pull the trigger while in SAFE mode (only if the safety lever has been removed)* and do not release the trigger.

  2. Switch the fire selector within 2 s. There is a single low frequency vibration.

  3. Switch the fire selector in any order to change between options, which are indicated by vibrations:

    1. 1 low vibration – Pre-cocking Off

    2. 2 low vibrations – Pre-cocking Auto

    3. 3 low vibrations – Pre-cocking Manual

  4. Release the trigger to save the selected mode.

Profile Selection

Profiles are sets of particular settings of configurable TITAN functions. You can choose one of the three profiles at a time. Go to General>Profiles>Change profile change via selector in GCS to be able to use this function. If you want to change the active Profile:

  1. Fire a shot, burst or pull the trigger while in SAFE (only if the safety lever has been removed) and do not release the trigger.

  2. Switch the fire selector within 2–7 s. There is a single high frequency vibration.

  3. Switch the fire selector in any order to change between options, which are indicated by vibrations. 

    1. 1 high vibration – Profile 1

    2. 2 high vibrations – Profile 2

    3. 3 high vibrations – Profile 3

  4. Release the trigger to save the selected profile.