Versions Compared

Version Old Version 6 New Version 7
Changes made by

Sebastian Florek-Paszkowski (Unlicensed)

Sebastian Florek-Paszkowski (Unlicensed)

Saved on

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.

...

  1. After unboxing and before installation, connect TITAN to the GCS App via Blu-Link or USB-Link. You can download GCS here: https://www.gatee.eu/gcs

    Image RemovedImage Added

    Image RemovedImage Added


    The GCS Information for Use is here: https://www.gatee.eu/manuals

    Image RemovedImage Added

  2. Check for latest firmware updates.

...

Caution
TITAN installation requires deep technical knowledge of gearbox internals. To avoid damage, we recommend it to be installed by a skilled person. If, however, you wish to proceed with TITAN installation on your own, you must watch the installation video and read the full-length PDF manual: https://www.gatee.eu/manuals beforehand. Incorrect installation may result in amongst among others sensor damage, which is not covered by warranty.

...

Info

Note  
TITAN V2 and TITAN V3 do not support Infinite torque-up gears.

...

Info

Note
In the case of some triggers (e.g. speed or CNC triggers), the first trigger sensor(s) may be covered even when the trigger is not pulled, which is due to its design.

Info

Note
The fire selector Fire Selector sensor does not detect black surface. If the fire selector Fire Selector does not come with a metal connector or it does not work properly, you must use an appropriate sticker from the kit.

...

Caution

Use a metal washer with a max. 8 mm [0.31 in] diameter to avoid TITAN damage.

...

Info

Note
Use the trigger sticker to make it visible for the trigger sensor.

...

Info

Note
TITAN can detect trigger position very precisely. In order to use it, you need to eliminate trigger backlash. The set contains 3 trigger anti-backlash stickers of various thicknesses. Try each one of them and choose the most appropriate one.

...

Info

Note
The selector plate requires modification. Place the selector sticker according to the photos below. Its position is crucial.

...

Info

Caution

In TITAN V3 the connectors must be straight according to the photo below. Bending and straightening the connectors back may cause them to break. If this happens, spare terminals are included in the installation kit.

...

TITAN V2 NGRS

Note

Warning
If you are using a recoil system and set excessive trigger sensitivity, it may cause incidental discharge (firing) even without pressing the trigger.

...

You can access Pre-cocking or Profiles using a shortcut. After firing a shot, burst or while in SAFE (only if the safety lever has been removed)*, hold the trigger and switch the fire selector Fire Selector within the specified time (see table). Switch the fire selector Fire Selector in any order to change between options indicated by motor vibrations. 

...

  1. Fire a shot, burst or pull the trigger while in SAFE mode (only if the safety lever has been removed)* and do not release the trigger.

  2. Switch the fire selector Fire Selector within 2 s. There is a single low frequency vibration.

  3. Switch the fire selector Fire Selector in any order to change between options, which are indicated by vibrations:

    1. 1 low vibration – Pre-cocking Off

    2. 2 low vibrations – Pre-cocking Auto

    3. 3 low vibrations – Pre-cocking Manual

  4. Release the trigger to save the selected mode.

...

  1. Fire a shot, burst or pull the trigger while in SAFE (only if the safety lever has been removed) and do not release the trigger.

  2. Switch the fire selector Fire Selector within 2–7 s. There is a single high frequency vibration.

  3. Switch the fire selector Fire Selector in any order to change between options, which are indicated by vibrations. 

    1. 1 high vibration – Profile 1

    2. 2 high vibrations – Profile 2

    3. 3 high vibrations – Profile 3

  4. Release the trigger to save the selected profile.