Versions Compared

Version Old Version 3 New Version 4
Changes made by

Sebastian Florek-Paszkowski (Unlicensed)

Sebastian Florek-Paszkowski (Unlicensed)

Saved on

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.

GATE Control Station (GCS)


The GATE Control Station GCS enables you to update the firmware and adjust the settings using the USB-Link or BlueBlu-Link and the GATE Control Station™ GCS App. With GCS, you do not have to remember complicated trigger Trigger sequences to program your unit. All features are easily accessible and simple to adjust with just one click.

Tip

Note
GCS can be used both on

...

desktop and mobile devices.

We are constantly improving our applicationsthe GCS App. Each update brings new features and/or corrections. All changes are available in our changelog: https://gatee.eu/technical-support/changelog

...

  • update and upgrade TITAN firmware

  • change all TITAN settings

  • calibrate the trigger Trigger and fire selectorSelector

  • set trigger Trigger sensitivity

  • check the status of your TITAN sensors

  • check the statistics of your gun (Rate of Fire, trigger Trigger response etc.)

  • check Diagnostic Trouble Codes (DTCDTCs)

  • contact GATE Support Center (via error report, messenger or phone)

Tip

Note
You need a USB-Link to connect your TITAN to

...

GCS for Android and Windows/macOS. To connect to the iOS GCS, you must use a Blu-Link.

Tip

Note
You can find out how to program your device using the Blu-Link in the manual included in the Blu-Link kit.

Note

Caution
Prevent the USB-Link and the ends of the USB cable from contact with conductive materials, such as dust, liquid or metal powder.

Tip

Note
Do not remove the device heat shrink tube.

  1. Connect the USB-Link via its Micro-USB plug to into your PC, Mac or smartphone using one of the dedicated USB cables:

...

Micro-USB or USB-C cable for smartphones

Tip

Note
The micro-USB cable has the same connectors on both sides. However, it is very important to connect the USB-Link and smartphone to the appropriate ends of the cable as otherwise, it will not work. 

...

Tip

Note
If your USB-Link cannot be detected, follow the instructions displayed in the

...

GCS.

  1. Connect TITAN to the USB-Link.

...

 Restore Factory Settings – (hard reset) restores all default settings, resets your statistics, and clears adaptation data.
Cycle detection – allows to switch OFF or ON the optical gear sensor. Cycle detection OFF can be compared with the “emergency mode” for troubles with gear sensor. Most of TITAN features will be disabled, but you can still shoot on ‘AUTO’.
Thanks to the gear sensor, TITAN precisely detects in which position the cycle should finish. Therefore, even the shortest trigger Trigger action produces at least one full cycle.

...

Battery protection – modern LiPo and LiFe batteries are very sensitive to over-discharge. The microprocessor monitors the battery voltage constantly. When the voltage drops down to a critical level, it will not allow firing.
Battery cell – when the battery voltage drops to the specified level (in relation to one cell), the motor will vibrate. You can set: OFF, 3.2V or 3.4V per cell for LiPo battery and 2.7V or 2.9V per cell for LiFe battery.
30-Round Limit – an AEG can continuously fire max. 30 BBs. To fire more BBs, you must release the trigger Trigger before. This is protection against trigger Trigger jam. Important: in case of emergency, you can also stop firing by switching the fire selector Selector position.

Active brake - it automatically adjusts the motor’s braking power according to your needs. This prolongs the lifespan of the motor and reduces the heat. Now you can also choose your own value depending on your needs.
Gear ratio - to make the PRE-COCKING work with the highest level of precision you should define the gears type in your AEG. Available types: STANDARD, HIGH TORQUE, HIGH SPEED, DSG, 19-TOOTH.
Typical gear ratio settings (excluding DSG and 19-tooth):
HIGH TORQUE: <15 RPS
STANDARD: 15-25 RPS
HIGH SPEED: >25 RPS
If overspin issue occurs, you should switch the gear type to the next level (e.g. STANDARD to HIGH TORQUE).
Note
Regional lock designed for German players will disable all the burst and auto options.
Note
The DSG and 19-TOOTH gear ratio options are not available for TITAN V2 NGRS.

...

Pre-cocking – allows for initial spring compression, which speeds up the trigger Trigger response significantly:
AUTO MODE – the spring is automatically compressed after each shot
TRIGGER Trigger MODE – slow trigger Trigger action compresses the spring, and fast trigger Trigger action fires the shot
Please note: using PRE-COCKING increases wear and tear on the gearbox.

Pre-cocking boost – determines the strength of spring compression. The highest setting results in the best trigger Trigger response, but also mostly increases wear and tear on the gearbox.
If you are facing overspin issue, set GEAR RATIO to HIGH SPEED.

Burst mode:
FULL – every, even the shortest trigger Trigger action fires the pre-determined number of
rounds
TRIGGER Trigger – releasing the trigger Trigger while firing stops the burst sequence.
Burst – allows you to set how many BBs will be fired
ROF stabilization:
ON – ROF Control uses PWM (Pulse Width Modulation) to decrease ROF. Thanks to this, gearbox works smoothly what decreases wear and tear of AEG internal parts. The percentage value determines the PWM duty cycle and it does not reflect ROF decrease.
OFF – ROF Control adds breaks between shots to decrease ROF. It gives you more realistic experience. This option set to 50% will significantly reduce the rate of fire.
ROF control – enables a reduction in a gun’s rate of fire. You use stronger LiPo batteries, and still have a ROF just like in a real gun.

...

Sniper delay – lets you to set delay between each SEMI shots to simulate the delay from reload or recoil. You can set 0.5s, 1s, 2s or 3s delay. By choosing ‘VIB’ option, you can enable vibration which will inform you when the gun is ready to fire again.

Equalizer (dynamic trigger Trigger point):
OFF - to fire the next shot, you need to release the trigger Trigger until it reaches the selected trigger Trigger sensitivity level
2LVL - to fire the next shot, it is enough to release the trigger Trigger so as it changes the state of two trigger Trigger sensors or ~40% of trigger Trigger movement
1LVL - to fire the next shot, it is enough to release the trigger Trigger so as it changes the state of one trigger Trigger sensor or ~20% of trigger Trigger movement

1LVL or 2LVL are especially useful when the trigger Trigger sensitivity level is very high. Then you do not need to fully release the trigger Trigger while quickly firing on SEMI.

...

We designed the Sensors TAB in order to let you choose the  trigger Trigger sensitivity or ‚ trigger Trigger mode that is the best for you. Thanks to live view, you do not need to mechanically adjust your triggerTrigger. Simply choose the value and check if it suits you.

You will be warned if the trigger Trigger sensitivity value reaches extremely low level.

Selector

Fire selector Selector mode – allows you to choose how your replica will behave on each fire selector Selector position:
SAFE – replica will not fire after trigger Trigger pull
SEMI – one pull of the trigger Trigger will result in only one shot
BURST – one pull of the trigger Trigger enables you to shoot a pre-determined number of BBs, which is very useful in MILSLIM and when using low-caps
AUTO – pulling the trigger Trigger causes uninterrupted* series of shots until the trigger Trigger is released
*series can be limited by Round Limit

...

Note
Statistics are saved every ten seconds. If you want to save your statistics immediately, switch the fire selector Selector to SAFE.

Diagnostics

Diagnostic Trouble Codes (DTC) tab

...