...
Click here 1️⃣ to go to Restore Default Settings 2️⃣ – restores default settings for the various functionalities. Trigger and selector Selector calibration as well as statistics Telemetry data remain unchanged and 3️⃣ Restore Factory Settings – (hard reset) restores all default settings, resets your statisticsTelemetry, and clears adaptation data.
...
7️⃣ Battery protection – modern LiPo and LiFe batteries are very sensitive to overdischarge. The microprocessor monitors the battery voltage constantly. When the voltage drops down to a critical level, it will not allow firing. Battery cell – when the battery voltage drops to the specified level (in relation to one cell), the motor will vibrate. You can setAvailable settings: OFF, 3.1 V, 3.2 V, 3.3 V or 3.4 V per cell for LiPo batteries and 2.6 V, 2.7 V, 2.8 V or 2.9V per cell for LiFe batteries.
...
9️⃣ Gear Ratio - to activate PREPre-COCKING work Cocking with the highest level of precision you should define the gears gear type in your AEG. Available ; available types: Normal Speed, Low Speed, High Speed, DSG*, 19-Tooth*.
Typical gear ratio settings (excluding DSG and 19-tooth):
Low Speed: <15 RPS
Normal Speed: 15-25 RPS
High Speed: >25 RPS
If overspin issue occurs, you should switch the gear type to the next level one (e.g. Normal Speed to Low Speed).
| Tip |
|---|
Note |
🔟 Active brake - it Brake automatically adjusts the motor’s motor braking power according to your needs. This prolongs the lifespan of the motor and reduces the heat. Now you can also choose your own value depending on your needs.
| Tip |
|---|
Note |
Trigger
...
2️⃣ Pre-cocking – Cocking allows for initial spring compression, which speeds up the Trigger response significantly:
AUTO MODE Auto – the spring is automatically compressed after each shot
Trigger MODE – slow Trigger action compresses the spring, and fast Trigger action fires the shot
Please note: using PRE-COCKING increases wear and tear on the gearbox.Pre-cocking boost – . In Auto you can also set Boost, which determines the strength of spring compression. The highest setting results in the best Trigger response, but also mostly increases wear and tear on the gearbox.
If you are facing overspin issueoccurs, set GEAR RATIO to HIGH SPEED.
Burst mode:
FULL – every, even the shortest Trigger action fires the pre-determined number of
rounds
Trigger – releasing the Trigger while firing stops the burst sequence.
Burst – allows you to set how many BBs will be fired
3️⃣ ROF stabilization:
Gear Ratio to High Speed.
| Tip |
|---|
Note |
Manual – you can set the values SEMI, BURST, and AUTO.
screen
3️⃣ ROF Control enables a reduction in a gun’s Rate of Fire. You can use stronger LiPo batteries, and still have a ROF just like in a real gun. ON – ROF Control uses PWM (Pulse Width Modulation) to decrease ROF. Thanks to this, the gearbox works smoothly what , which decreases wear and tear of AEG internal parts. The percentage value determines the PWM duty cycle and it does not reflect ROF decrease.
OFF – ROF Control adds breaks between shots to decrease ROF. It , which gives you a more realistic experience. This option set to 50% will significantly reduce the rate of fire.
ROF control – enables a reduction in a gun’s rate of fire. You use stronger LiPo batteries, and still have a ROF just like in a real gun.
4️⃣ You don't need to fully release the trigger Trigger to fire the next shot. This option is really useful when the trigger Trigger sensitivity level is very high. Choose between two types of Equalizer.:
1LVL, 2LVL and MANUAL are especially useful when trigger sensitivity level is very high, so you do not need to fully release the trigger while firing quickly:
...
OFF – to fire the next shot, you need to release the trigger until it reaches the selected trigger sensitivity level.
2LVL – to fire next shot, just release the trigger so it changes the position by ~40% of trigger movement.
1LVL – to fire next shot, just release the trigger so it changes the position by ~20% of trigger movement.
MANUAL – thanks to EXPERT firmware, you can adjust the percentage of trigger movement exactly as you prefer. This option is not available in TITAN V2 because of sensors type.
5️⃣ Sniper delay – Delay lets you to set delay between each SEMI shots shot to simulate the delay from reload or recoil. You can set it between 0.5s, 1s, 2s or 3s delay01 and 5 s. By choosing ‘VIB’ the Manual with Vibration option, you can enable a vibration which will inform you when the gun is ready to fire again.
We designed the Sensors TAB in order to let you choose the Trigger sensitivity or Trigger mode that is the best for you. Thanks to live view, you do not need to mechanically adjust your Trigger. Simply choose the value and check if it suits you.
You will be warned if the Trigger sensitivity value reaches extremely low level.
Selector Selector
...
Selector mode – allows you to choose how your replica will behave on in each Selector position:
SAFE – the replica will not fire after when the Trigger pullis pulled
SEMI – one pull of the Trigger will result in only one shot
BURST – one pull of the Trigger enables you to shoot a pre-determined number of BBs, which is very useful in MILSLIM MILSIM and when using low-caps
AUTO – pulling the Trigger causes an uninterrupted* series of shots until the Trigger is released
*the series can be limited by the Round Limit.
Magazine
Alerts
...
Telemetry
The statistics tab Telemetry contains main information about your replica replica’s performance. You can simply clear each value by clicking “Reset” the Reset button. You can also independently reset BB1 and BB2 counter.
TITAN gives you the option to check:
Rate of fire ROF - Minimum, Average, Maximum
Trigger response - Minimum, Average, Maximum
Module’s Module temperature - Minimum, At this moment, Maximum
Motor current - Average AUTO, Average SEMI, Maximum Peak
Battery voltage - Minimum, Last, Maximum
Number of fired BBs - BB1, BB2, TOTAL
Note
Statistics Telemetry data are saved every ten seconds. If you want to save your statistics Telemetry data immediately, switch the Selector to SAFE.
...
Diagnostic Trouble Codes (DTC) tab
This TAB will help you to troubleshoot your replica in case of any issue. If you need additional help, you can contact our Support Center using “SEND REPORT” button, or save the report using “SAVE TO FILE” button.
...