Versions Compared

Version Old Version 120 New Version 121
Changes made by

Sebastian Florek-Paszkowski (Unlicensed)

Sebastian Florek-Paszkowski (Unlicensed)

Saved on

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.

...

Blu-Link allows you to control GATE devices such as TITAN, ASTER, and STATUS and connect it them to other compatible ones wirelessly via the GCS App. What’s more, Blu-Link is an additional adjustable smart fuse and multifunctional wattmeter enabling you to, e.g., read Telemetry data.

...

Warning

Warning
Persons under 18 years of age ought not stay unattended near the device during the its installation or servicing of a device installed in an ASG replica.

Warning

Warning
Persons under 18 years of age ought not stay unattended near the device installed in an ASG replica ready for use.

...

Technical Specifications

Supply voltage rangeVoltage Range

4,75-17 VDC

Rated voltageVoltage

11,1 VDC

Nominal current consumptionCurrent Consumption

280 uA

Maximum current consumptionCurrent Consumption

45 mA (for 17 VDC)

Dimensions (length Length x width Width x thicknessThickness)

54,5 mm x 19,9 mm x 9 mm

Finished product weightProduct Weight

9,65 g

Operating temperature rangeTemperature Range

min. -15° C, max. +50° C

Relative humidityHumidity

≤ 80%

How to Use Blu-Link

...

Tip

Note
You can use Blu-Link without an ETU. It will work as a smart fuse and a multifunctional wattmeter enabling you to, e.g., read Telemetry data.

...

LED

What happened:

What to do:

1 s on start

Self-test completed successfully

  • Blu-Link is OK

  • Wait for further LED indications

Blu-Link has been connected correctly

 

BLINKING for 120 s

Blu-Link is ready for Bluetooth connection®

Connect Blu-Link to GCS

Self-test failed, Bluetooth® connection is not possible

  • Disconnect the power supply from Blu-Link, wait 10 seconds and reconnect the power supply

  • If you have a USB-Link, connect it to the INPUT Blu-Link connector, go to Diagnostics in GCS, check Blu-Link DTCs and follow the instructions there

  • Contact us at support@gatee.eu

BLINKING

  • No Blu-Link firmware installed

  • Self-test failed, Bluetooth® connection is possible

  • Install Blu-Link firmware via GCS

  • Connect Blu-Link to GCS, go to Diagnostics in GCS, check Blu-Link DTCs and follow the instructions there

for 120 s

Blu-Link is connected correctly via Blutooth®

Enjoy using Blu-Link

Blu-Link firmware update in progress

  • Wait until the firmware has been updated

  • Keep the device with GCS as close as possible to Blu-Link

  • Battery saving mode

  • Battery disconnected

  • Enjoy using Blu-Link

  • Connect battery

  • The battery is discharged Discharged or damaged battery

  • Battery Deans-T connector is not compatible

  • Damaged power cables

  • Charge or replace the battery

  • Use the Deans-T battery connector included with the INSTALLATION KIT

  • Replace power cables

BLINKING 

Overload, DTC displayed: 2 – ULL, 3 – OCP, 4 – SCP, 5 – OTP

Read what to do in the next section or connect Blu-Link to GCS and check the Diagnostics tab

BLINKING

Excessively low voltage, DTC displayed: 1 – UVP1, 2 – UVP2, 3 – UVP3

Read what to do in the next section or connect Blu-Link to GCS and check the Diagnostics tab

...

  1. The LED color reflects the problem type:

    • Yellow indicates a warning

    • Red indicates a problem

  2. The number of blinks determines what exactly the problem is.

...