Content Comparison

The most common mistakes:

1. Washer

...

Issue

1. User's fault:

   Placing the

   placing washers in wrong order

   .

2. Result:

   Short

   short circuit and permanent damage to

   the

   TITAN

   .

3. How to detect?
   

Correct order:

...

2. Trigger sensors damageSensor Damage

1. User's fault:

   Pulling

   pulling the trigger when the gearbox is open

   .

2. Result:

   Tearing

   torn off trigger sensors

   .

   
   TITAN will not be able to detect all 5 trigger sensitivities even

   while

   if using a standard trigger (please note that in the case of speed triggers TITAN

   also

   cannot detect all trigger sensitivities

   and it doesn’t

   either, which does not mean that sensors are damaged).

3. How to detect?

   Trigger

   missing trigger sensors (receivers)

   are missing.

...

...

3. Cables damageCable Damage

1. User's fault:

   Incorrect

   incorrect cable routing

   .

2. Result:

   Damaging or total tearing the

   damaged or torn off wires by motor gear

3. How to detect?

   Insulation is

   damaged

   .

   insulation
   

...

...

4. Capacitor damageDamage

1. User's fault:

   Mounting

   mounting TITAN V2 in an ICS gearbox without necessary modifications

2. Result:

   Gearbox latch is damaging or total tearing

   the gearbox latch has damaged or torn the yellow capacitor

3. How to detect?

   Yellow

   the yellow capacitor is missing or damaged
   
   

...

5. Gear sensor damageSensor Damage

1. User's fault:

   Too

   very low shimming of sector gear

2. Result:

   Tearing

   torn off gear sensor

   .

3. How to detect?

   Gear

   missing gear sensor

   is missing.

   
   

...

...

Less frequently encountered:

 6. Fire selector sensor damage Fire Selector Sensor Damage

1. User's fault:

   Incorrect

   incorrect bottom board placement in gearbox shell

2. Result:

   Tearing

   torn off

   fire selector

   Fire Selector sensor

   .

3. How to detect?

   One

   one of the trigger sensors

   is

   missing

7. Motor connector damage

1. User's fault:

   Using

   using too much force during motor connector bending, bending connector to wrong side

...

...

1. Result:

   Braking

   broken motor connector

2. How to detect?

   Motor

   motor connector

   is

   broken in half

 8. Reverse  Reverse polarity

1. User's fault:

   Plugging

   plugging a battery

   to

   into the unit in incorrect order (a negative wire with a positive wire and a positive wire with a negative wire)

2. Result:

   Destroying

   destroying the main parts of the board

3. How to detect?

   Unit

   theunit is not responding,

   whole

   the entire board is

   burned

   burnt

...

9. Wire damage Damage (caused Caused by triggerTrigger)

1. User's fault:

   Incorrect

   incorrect wire placement in gearbox shell

2. Result:

   Tearing

   torn wire insulation

3. How to detect?

   Wire

   tornwire insulation

   is teared

   close to the trigger

 10. Short circuit caused by damaging cables insulation Short Circuit Caused by Damaging Cable Insulation

1. User's fault: Cutting both positive and negative

   wire

   wires with body of the replica

2. Result: Insulation damage, short circuit

3. How to detect?

   Burned

   Burnt wires from a cut place

11. Repairs or structural modification Structural Modification of any TITAN part, including re-wiring Part (including rewiring and component replacement)

1. User's fault:

   Interference

   interference in the

   construction

   structure of the unit

2. Result:

   Automatic

   automatic warranty loss

   of the warranty

3. How to detect?

   Visible

   visible changes

   like

   such as different wire color

...

Cases when warranty should be accepted:

1. Constantly occurring errors from

   recurring E01 to E06

   and

   , E13, E14, and E15 errors

2. Total

   total absence of reaction from the unit without visible damage

3. No

   no connection with

   the

   USB-Link and/or

   programming card

   Tactical Programming Card even if the unit is working properly without any visible damage (no programming option)

4. Continuous occurrence

   recurrence of error E07 combined with no cycle detection (after very accurate troubleshooting)

Related articles

...