...
| Note |
|---|
Caution |
| Note |
|---|
Caution |
| Tip |
|---|
Note
|
Installation Instruction
Remove all components from the package.
Prepare the chamber body and the rotary dial.
Gently lubricate the o-ring of the rotary dial with grease (e.g. silicone).
Push the rotary dial until it rests against the chamber body. This may require more force.
Disassemble your current chamber and remove its barrel.
Clean the barrel with a cleaning pad or a wipe.
Prepare a hop-up bucking and a tensioner (you can use the same parts or new ones).
Put the hop-up bucking on the barrel (pay attention to the stabilizing groove in the barrel - the barrel—the elongated protrusion in the bucking should is supposed to fit perfectly into it.
Lubricate the bucking gently with grease - just grease—just like when installing the rotary dial (you can use the same grease).
Spread the grease on the outer surface with your fingers, leaving a thin layer of grease.
Insert the bucking into the chamber with gentle back and forth movements until it rests on the bottom of the socket in the chamber.
In the final stage, pay attention to whether make sure the bucking chafes does not chafe against the tensioner window. If you are unable to get the barrel into place, carefully lubricate the bucking again and try once more. If the problem persists, try using other hop-up bucking because this one is too large in diameter.
Set the barrel straight in the chamber - with chamber—with the incision on the barrel perfectly in the axis of symmetry of the chamber.
Install the barrel latch (this may require gently moving the barrel back and forth) - for —for bucking with a longer flange, (such as Maple Leaf) use a latch with a longitudinal incision.
If the latch is in place you will hear a distinct click.
Install the barrel bushing.
Place the tensioner in the tensioner socket.
Place the nub in the guides - if guides—if using a standard tensioner, install the nub as shown. For FLAT/BRIDGE type tensioners with an enlarged window in the barrel, rotate the nub 180°.
Place the hop-up arm so that one end rests on the rotary dial and the other on the tensioner nub.
Screw in the mounting screw.
Sprawdź zakres regulacji oraz czy wszystko zostało zainstalowane prosto. Docisk powinien układać się horyzontalnie. Jeśli widzisz jakieś odchylenia, popraw instalację lufy i gumki w komorze.
Na lufie umieść kilka o-ringów dociskowych.
Dosuń lufę z komorą do przedniej ściany korpusu. Dystans między korpusem a komorą powinien wyglądać mniej więcej tak, jak na zdjęciu poniżej.
Jeśli użyto zbyt wielu o-ringów i w Twojej replice komora wystaje bardziej—usuń jeden lub kilka o-ringów. Dopasuj ich ilość tak, by wciśnięcie przedniego pina wymagało użycia siły, a komora nie miała żadnego luzu w przód i tył. Ilość o-ringów może się różnić w zależności od producenta repliki.
Jeśli w Twojej replice komora ma duże odchylenia w osi (na boki), to skrzydełka stabilizacyjne są zbyt luźne (będzie się to różnić w zależności od producenta repliki). Aby zniwelować ten luz, użyj naklejek do kasowania luzu. Dotnij je zgodnie z rysunkiem a następnie naklej na powierzchnie skrzydełek.
...
| Info |
|---|
Koniec części dotyczącej replik AEG - komora jest gotowa do użycia w replice AEG. Poniżej znajdziesz krok opisujący instalację tulejki dyszy z silnikami HPA. |
Niektóre silniki HPA posiadają zbyt luźną dyszę, co negatywnie wpływa na działanie repliki oraz potęguje mid-cap syndrom. Warto wtedy zastosować dołączoną do EON Hop-Up tulejkę dyszy, która minimalizuje to zjawisko.
...
| Note |
|---|
Uwaga Fioletowa dysza silnika PULSAR S nie wymaga stosowania tulei stabilizującej w komorze hop-up. Stosowanie tulei stabilizującej z fioletową dyszą może negatywnie wpływać na działanie silnika. Złota dysza silnika PULSAR S może wymagać dodatkowej stabilizacji. W tym przypadku zaleca się stosowanie tulei stabilizującej w komorze hop-up. |
...
Check the rotary dial range and that everything has been installed straight. The nub is supposed to line up horizontally. If you see any deviation, correct the installation of the barrel and the bucking in the chamber.
Place some pressure o-rings on the barrel.
Bring the barrel with the chamber to the front wall of the barrel. The distance between the barrel and the chamber should look more or less as in the photo below.
If too many o-rings have been used and in your replica the chamber sticks out more—remove one or more o-rings. Adjust the number of them so that it takes force to push the front pin in, and the chamber has no back and forth backlash. The number of o-rings may vary depending on the manufacturer of the replica.
If in your replica the chamber has a large deviation in axial alignment (sideways), then the stabilizing wings are too loose (this will vary depending on the manufacturer of the replica). To eliminate this backlash, use backlash erasing stickers. Cut them according to the drawing and then stick them on the surfaces of the wings.
...
| Info |
|---|
The end of the part for AEG replicas—the chamber is ready for use in an AEG replica. Below you will find a step describing the installation of the nozzle sleeve with HPA engines. |
Some HPA engines have an excessively loose nozzle, which negatively affects the performance of the replica and intensifies the mid-cap syndrome. It is then worth using the nozzle sleeve included with the EON Hop-Up, which minimizes this phenomenon.
...
| Note |
|---|
Caution |
...
Technical Specifications
Hop-Up Chamber Weight | 15 g |
|---|
Legal Notice
Please read this Legal Notice before operating your device and keep it for future reference.
This document contains important terms and conditions with respect to your device. By using this device, you accept those terms and conditions.
Exclusion of Liability
GATE Enterprise sp. z o.o. sp. k. are not liable for any damages, injuries or accidents of any kind resulting from the use of this product or airsoft gun with the product installed, including (but not limited to) incidental or intentional damages to airsoft gun, airsoft gun parts, batteries and gearbox internals.
Disclaimer
GATE Enterprise sp. z o.o. sp. k. take no responsibility regarding compliance of the product with the requirements of any law, rule or airsoft restrictions pertaining thereto.
Intellectual Property
Intellectual Property owned by GATE Enterprise sp. z o.o. sp. k., including (but not limited to) devices, accessories, parts, software, documentation, is proprietary to GATE Enterprise sp. z o.o. sp. k. and protected under Polish laws, EU laws and international treaty provisions. You may not violate the rights of the Intellectual Property and you will not prepare derivative works of or reverse engineer the device or software. No ownership in the Intellectual Property is transferred to you.
GATE Limited Warranty Policy
GATE Enterprise sp. z o.o. sp. k. warrant that their product is free from manufacturing and material defects at the date of purchase and for a non-extendable period of two (2) years from the date of purchase. This Limited Warranty is conditioned upon proper use of the product by Purchaser.
This Limited Warranty is valid provided that the owner provides a proof of purchase and a properly completed warranty form.
This Limited Warranty does not cover: (a) defects or damage (e.g., mechanical, thermal or chemical) resulting from accident, misuse (misinterpretation of the instructions), abuse, neglect, unusual physical, electrical or electromechanical stress, water immersion, repairs or structural modification of any part of the product, or (b) the product that has its serial number removed or made illegible; (c) defects or damage from improper operation, maintenance or installation; (d) installation of the products.
Requests for warranty are processed as soon as possible, not exceeding 7 (seven) working days. The company’s obligation under this Limited Warranty shall be limited to providing replacement of part(s) only.
Product disposal instructions
The symbol shown indicates that the product can be recycled.
...
Stay tuned with GATE
http://facebook.com/Gatee
http://youtube.com/GateMovies
http://instagram.com/GateEnterprise
Manufactured by
GATE Enterprise sp. z o.o. sp. k.
Torowa 3H
PL-30435 KRAKÓW
email: office@gatee.eu
tel: +48 12 210 05 23