| Table of Contents | ||||
|---|---|---|---|---|
|
...
Fire a shot, burst or pull the trigger while in SAFE (only if the safety lever has been removed) and do not release the trigger.
Switch the selector within 2–7 s. There is a single high frequency vibration.
Switch the selector in any order to change between options, which are indicated by vibrations.
1 high frequency vibration – Profile 1
2 high frequency vibrations – Profile 2
3 high frequency vibrations – Profile 3
Release the trigger to save the selected profile.
Programming
...
via USB-Link
| Tip |
|---|
Note |
| Tip |
|---|
Note |
Turning on Programming Mode
Switch the selector on your replica to SEMI or BURST.* If AUTO mode is selected in SEMI position, use the alternative method below.
Fire a shot or burst and do not release the trigger.
Hold the trigger for 7 seconds – until you hear a vibration.
*Not possible if AUTO mode is selected in SEMI position.
...
Alternative Method
Disconnect the battery
Pull the trigger and do not release it
Connect the battery (ignore the warning vibrations)
Hold the trigger for 3 s – until you hear a vibration
You can easily change the menu level by switching the selector. Pull the trigger to quickly navigate the menu. Each time you pull the trigger, the number of accompanying vibrations changes. The table presents functions and their options programmable via trigger as well as how they are indicated by vibrations.
| Tip |
|---|
Note |
...
*To execute an action from Advanced, hold the trigger down for more than 3 seconds.
**This needs to be predefined in the GCS and is then available at trigger level. Once you disconnect the battery, the setting cannot be changed and needs to be reintroduced in GCS.
***Not available for TITAN V2 NGRS.
Selecting a Function
Switch the selector to SEMI.
To get to a function, pull the trigger the specified number of times (according to the table above).
Selecting an Option of a Function
Switch the selector to AUTO.
To get to an option of a selected function, pull the trigger the specified number of times (according to the table above).
Advanced Options
Select the Advanced option.
Pull and hold the trigger for more than 3 seconds.
Saving an Option
To save an option, switch the selector to SEMI.
The setting is saved and you are back to the functions menu.
You can set the options of the other basic functions the same way.
Exiting the Programming Mode
Switch the selector to SAFE.
Enjoy the TITAN functions you've just set.
Activating SAFE Mode if Not Assigned
If SAFE mode is not assigned in GCS, it is possible to activate it via the selector*:
Switch the selector rapidly in this sequence: SAFE → SEMI → SAFE (SAFE → AUTO → SAFE for AK-47).
Now SAFE mode is activated – switch to SEMI or AUTO to deactivate it.
Switching to SAFE again accesses the fire mode assigned to the SAFE position in the GCS.
*SAFE mode also applies when the selector is in SAFE while connecting the battery – switching to SEMI or AUTO deactivates it.
https://www.youtube.com/watch?v=yD-a-htaXOs
...
| Tip |
|---|
Note |
Programming via USB-Link
| Tip |
|---|
Note |
| Note |
|---|
Caution |
| Note |
|---|
Caution |
1. Connect the USB-Link via its Micro-USB plug to your PC, Mac or smartphone using one of the dedicated USB cables:
USB-A cable for PC/Mac
Micro-USB or USB-C cable for smartphones
| Tip |
|---|
Note |
...
| Tip |
|---|
Note |
2. Connect TITAN to the USB-Link.
| Tip |
|---|
Note
|
3. Now you can control TITAN via GCS.
USB-Link Troubleshooting
The USB-Link has a 4-color LED indicator.
...
Restoring Factory Settings
| Tip |
|---|
Note |
| Tip |
|---|
Note |
You can restore Factory Settings in 3 ways:
Via GCS:
Go to General. Open the menu in the upper right corner and select Restore factory settings.
...
While in programming mode (only for TITAN V2):
Turn on the programming mode as described in Programming via Trigger
Switch the selector to SEMI
Pull the trigger 5 times to select Advanced (6 vibrations)
Switch the selector to AUTO
Pull the trigger to get to Restore Factory Settings (4 vibrations)
Confirm the Restore Factory Settings option by pulling the trigger for at least 3 seconds
While connecting the battery (only for TITAN V2):
Disconnect the battery
Pull the trigger
While the trigger is pulled, connect the battery (ignore the warning vibrations)
Hold the trigger for 10 seconds until you hear 2 vibrations confirming the reset (ignore the vibrations occurring in the meantime informing about entering the programming mode)
Release the trigger
| Tip |
|---|
Note |
| Note |
|---|
Caution |
| Note |
|---|
Caution |
1. Connect the USB-Link via its Micro-USB plug to your PC, Mac or smartphone using one of the dedicated USB cables:
USB-A cable for PC/Mac
Micro-USB or USB-C cable for smartphones
| Tip |
|---|
Note |
...
| Tip |
|---|
Note |
2. Connect TITAN to the USB-Link.
| Tip |
|---|
Note
|
3. Now you can control TITAN via GCS.
USB-Link Troubleshooting
The USB-Link has a 4-color LED indicator.
...
Restoring Factory Settings
| Tip |
|---|
Note |
| Tip |
|---|
Note |
You can restore Factory Settings in 3 ways:
Via GCS:
Go to General. Open the menu in the upper right corner and select Restore factory settings.
...
Troubleshooting
Low Battery Warnings
...
TITAN V2 has the following optical sensors:
1 sector gear sensor
2 selector sensors
5 trigger sensors
...
Installation
Please read the installation guide below before proceeding.
...
TITAN V3 has the following optical sensors:
1 sector gear sensor
1 selector sensor
1 proximity trigger sensor
...
Installation
Please read the installation guide below before proceeding.
...
TITAN V2 NGRS has the following optical sensors:
2 gear sensors
1 selector sensor
1 trigger sensor
1 bolt catch sensor
...
Installation
Please read the Installation Guide below before proceeding.
...