Versions Compared

Version Old Version 199 New Version 200
Changes made by

Tomasz Sieja (Deactivated)

Sebastian Florek-Paszkowski

Saved on

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.
Table of Contents
minLevel1
maxLevel7

...

The information contained in this document is subject to change without notice for specification changes or other reasons. When using a product listed here be sure to obtain the latest specifications.

Installation

Note

Caution
Regardless of your previous experience, follow all safety precautions to prevent any damage to your TITAN.

...

Tip

Note
In case you have any difficulties while installing or using this product:

TITAN V2

...

Note

Caution
A sector gear can damage the gear sensor during installation. Avoid such damage.

...

Note

Caution
In TITAN V2 connectors must be bent according to the photo below. Bending connectors in the opposite direction may cause them to break. If this should happen, spare terminals are included in the INSTALLATION KIT.

...

TITAN V3

...

Tip

Note
TITAN V3 fits CNC gearboxes with very low backlash. While fitting TITAN, pull the cables and at the same time push the board into the right place. Pay attention to the area marked yellow to fit the board correctly. Do this carefully so as not to damage the insulation of the wires.

...

Tip

Note
Use the trigger sticker to make it visible for the trigger sensor.

Tip

Note
TITAN can detect trigger position very precisely. In order to increase sensitivity, you need to eliminate trigger backlash. The set contains 3 trigger anti-backlash stickers of various thicknesses. Try each one of them or a combination of more than one and choose the most appropriate one.

Tip

Note
The selector plate requires modification. Place the selector sticker according to the photos below. Its position is crucial.

Note

Caution
In TITAN V3 the connectors must be straight according to the photo below. Bending and straightening the connectors back may cause them to break. If this should happen, spare terminals are included in the INSTALLATION KIT.

TITAN V2 NGRS

...

Warning

Warning
If you are using a recoil system and set excessive trigger sensitivity, it may cause accidental discharge (firing) even without pressing the trigger.

...

Note

Caution
In TITAN V2 NGRS connectors should be bent according to the photo below. Bending connectors in the opposite direction may cause them to break. If this should happen, spare terminals are included in the INSTALLATION KIT.

...

Quick Access Menu

...

You can access Pre-Cocking or Profiles using a shortcut. After firing a shot, burst or while in SAFE (only if the safety lever has been removed)*, hold the trigger and switch the selector within the specified time (see table). Switch the selector in any order to change between the options indicated by motor vibrations. 

...

*You can enter Programming via Trigger only when the selector on the replica is in SEMI position and AUTO mode is not assigned to this position.

...

Pre-Cocking

In GCS go to Trigger>Pre-Cocking>Switch Mode via Selector and use the toggle button to activate this function.

  1. Fire a shot, burst or pull the trigger while in SAFE mode (only if the safety lever has been removed) and do not release the trigger.

  2. Switch the selector within 2 s. There is a single low frequency vibration.

  3. Switch the selector in any order to change between the options indicated by vibrations:

    1. 1 low vibration – Pre-Cocking Off

    2. 2 low vibrations – Pre-Cocking Auto

    3. 3 low vibrations – Pre-Cocking Manual

  4. Release the trigger to save the selected mode.

Profile Selection

Profiles are sets of particular settings of configurable TITAN functions. You can choose one of the three profiles at a time. Go to General>Profiles>Change Profile via Selector in GCS to be able to use this function. If you want to change the active profile:

  1. Fire a shot, burst or pull the trigger while in SAFE (only if the safety lever has been removed) and do not release the trigger.

  2. Switch the selector within 2–7 s. There is a single high frequency vibration.

  3. Switch the selector in any order to change between options, which are indicated by vibrations. 

    1. 1 high frequency vibration – Profile 1

    2. 2 high frequency vibrations – Profile 2

    3. 3 high frequency vibrations – Profile 3

  4. Release the trigger to save the selected profile.

Programming via USB-Link

Tip

Note
You can use a USB-Link to connect your TITAN to GCS for Android and Windows/macOS. To connect to GCS for iOS, you must use a Blu-Link.

...

3. Now you can control TITAN via GCS.

USB-Link Troubleshooting

The USB-Link has a 4-color LED indicator.

...

Restoring Factory Settings

Tip

Note
Restoring the factory settings results in resetting the default settings, erasing adaptations and statistical data.

...

Go to General. Open the menu in the upper right corner and select Restore factory settings.

...

Troubleshooting

Low Battery Warnings

When activated, you are warned 5 times before the battery is discharged. Each warning is communicated by 3 vibrations: High → Mid → High.

Vibrations after Connecting the Battery

TITAN can detect the number of battery cells automatically. If you activate this function, vibrations start once the battery is connected. Remember to always check if your TITAN detects the correct number of battery cells.

...

Diagnostic Trouble Codes

Diagnostic Trouble Codes (DTC) enable detecting basic malfunctions and problems with your AEG or TITAN. You are notified of the main errors by vibrations. DTCs can later be read and cleared in the DTC menu in GCS as well as in the Programming Mode in Advanced Settings.

...

Tip

Note
It is good practice to clear the DTCs in GCS before each skirmish.

...

TITAN V2

TITAN V2 has the following optical sensors:
1 sector gear sensor
2 selector sensors
5 trigger sensors

...

Installation

Please read the installation guide below before proceeding.

INSTALLATION KIT Contents

  • selector plate sticker set (6 pcs)

  • M2 screw and washer set:

    • 1 x screw

    • 1 x pressboard insulation washer

    • 2 x steel washers

  • M2.5 screw and washer set:

    • 1 x screw

    • 1 x pressboard insulation washer

    • 2 x steel washers

  • connector set:

    • 1 x Deans-T connector with heatshrink tubes

    • 2 x motor connectors (2.8 x 0.5 mm – 0.11 x 0.02 in) with heatshrink tubes

...

Procedure

You will need:

  • a cross-head screwdriver

  • a flat-blade screwdriver

  • a metal file or milling machine

  • solvent

  • grease

  • a Blu-Link or USB-Link with a micro USB-Cable and a Windows/Mac/Android/iOS device

...

Tip

Note
The first few shots are calibration shots. TITAN adapts to gearbox configuration. In order to readapt TITAN, you must Restore Factory Settings or change the Gear Ratio. This is necessary if e.g. you replace the motor.

TITAN V3

TITAN V3 has the following optical sensors:

1 sector gear sensor
1 selector sensor
1 proximity trigger sensor

...

Installation

Please read the installation guide below before proceeding.

INSTALLATION KIT Contents

  • 3 x selector plate stickers

  • trigger sticker set (6 pcs)

  • 3 x anti-backlash stickers (0.15 mm - 0.006 in)

  • 3 x anti-backlash stickers (0.3 mm - 0.012 in)

  • 3 x anti-backlash stickers (0.5 mm - 0.02 in)

  • 2 x washers (0.3 mm - 0.012 in)

  • 2 x washers (0.2 mm - 0.008 in)

  • 2 x washers (0.1 mm - 0.004 in)

  • set of connectors:

    • 1 x Deans-T connector with heatshrink tubes

    • 2 x motor connectors (2.8 x 0.5 mm - 0.11 x 0.02 in) with heatshrink tubes

...

Procedure

You will need:

  • a cross-head screwdriver

  • a flat-blade screwdriver

  • a metal file or milling machine

  • solvent

  • grease

  • Blu-Link or USB-Link with a micro USB-Cable and a mobile/desktop

...

Note

Caution
Calibrate the trigger and selector sensors only after the gearbox is mounted in the replica body.

...

TITAN V2 NGRS

TITAN V2 NGRS has the following optical sensors:

2 gear sensors
1 selector sensor
1 trigger sensor
1 bolt catch sensor

...

Installation

Please read the Installation Guide below before proceeding.

INSTALLATION KIT Contents

  • selector plate sticker set (6 pcs)

  • M2 washer set:

    • 2 x insulation pressboard insulation washers

    • 2 x insulation steel washers

  • connector set:

    • 1 x Deans-T connector with heatshrink tubes

    • 2 x motor connectors (2.8 x 0.5 mm – 0.11 x 0.02 in) with heatshrink tubes

...

Procedure

You will need:

  • a cross-head screwdriver

  • a Torx screwdriver

  • a flat-blade screwdriver

  • ametal file or milling machine

  • solvent

  • grease

  • a USB-Link with a micro USB-Cable or a Blu-Link and a Windows/Mac/Android/iOS device

...