Versions Compared

Version Old Version 26 New Version 27
Changes made by

Former user

Former user

Saved on

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.

...

Plug and play

  1. Attach Blu-Link to the AEG battery top side up

  2. If LED is glowing glows green, go to the next step. If not, see Blu-Link Troubleshooting Card (included in the kit)

  3. Connect the battery with attached Blu-Link to the AEG/ETU

  4. Place the battery in the stock

  5. Enjoy using Blu-Link

Notice
Blu-Link can stay attached connected all the time – you do not have to detach it after skirmish.

...

  1. Download and install GATE Control Station:
    www.gatee.eu/gcs

  2. Enable Bluetooth on your device (version 4.1 or later)

  3. Attach Blu-Link to the AEG battery top side upIf LED is glowing up

  4. If LED glows green, go to the next step. If not, see Blu-Link Troubleshooting Card (included in the kit)

  5. Log in to the GCS app

  6. Prepare PIN printed on Blu-Link box*

  7. Connect Blu-Link by following instructions displayed in GCS

  8. Connect the battery with attached Blu-Link to the AEG/ETU

  9. Place the battery in the stock

  10. Enjoy using Blu-Link

* First-time connection of You will need PIN code from the box when connecting Blu-Link and devices with GCS app requires authorization using PIN code from the boxfor the first time.

Notice
Keep the Blu-Link box or save PIN printed on it – you will need it in case the device is damaged, lost or stolen.

...

Diagnostic Trouble Codes (DTC) enable detecting inform about basic malfunctions and problems with your AEG/ETU or Blu-Link. You are notified of these main errors them with LED blinking for 2 minutes since the problem occurs. Blu-Lnik Link DTC can be later read and cleared in DTC menu in GCS app.

 

LED

WHAT HAPPENED

WHAT TO DO

UVP1
Protection against over-discharge of the battery. Battery protection was activated.

Charge the battery

UVP2
The voltage dropped below ??? V which is critical for Blu-Link to work properly.

a) If you have TITAN or ASTER, check its DTC in GCS app.

b) Otherwise, verify state of diagnose your ETU.

[Ad. a):

  1. Charge the battery

  2. Replace the battery

  3. Use a battery with more capacity or higher voltage

  4. Do not use any adapters

  5. Use standard or high-torque motors instead of high-speed

  6. Check and fix the motor wires insulation

  7. Unjam the motor

  8. Replace the motor]

 

UVP3
Protection against over-discharge of the battery. Battery protection was activated immediately after connecting the battery.

a) If you have TITAN or ASTER, check its DTC in GCS app.

b) Otherwise, verify state of diagnose your ETU.

[Ad. a):

  1. Set the same number of cells in GCS as in the battery

  2. Charge the battery]

OVL
Too high load. The load limit was exceeded.

???

OCP
Blu-Link detected too high current. Over current protection was activated.

a) If you have TITAN or ASTER, check its DTC in GCS app.

b) Otherwise, verify state of diagnose your ETU.

[Ad. a):

  1. Replace the motor

  2. Unjam the motor or gearbox

  3. Check and fix the motor wires insulation]

SCP
Blu-Link detected current over 240 A ???. Short circuit protection was activated.

a) If you have TITAN or ASTER, check its DTC in GCS app.

b) Otherwise, verify state of diagnose your ETU.

[Ad. a):

  1. Replace the motor

  2. Unjam the motor or gearbox

  3. Check and fix the motor wires insulation

OTP
Blu-Link temperature is too high. Over temperature protection was activated.

Wait until the temperature drops

...