Versions Compared

Version Old Version 32 New Version 33
Changes made by

Former user

Marcin Menet

Saved on

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.

Congratulations on your Blu-Link!

It allows you to control your GATE ETU and connect it with other compatible devices wirelessly via GATE Control Station app. Moreover, Blu-Link is an additional smart fuse and wattmeter enabling to, i.e., read telemetry data.

Together with GCS, you can adjust TITAN or ASTER settings and update or upgrade their firmware from devices with Android, iOS, Windows or macOS.

or

It allows you to easily update firmware and adjust settings of a compatible GATE device, using the GATE Control Station app. Moreover, Blu-Link is an additional fuse and wattmeter enabling to, i.e., read telemetry data. With the GCS app, you can control your airsoft gun from smartphone or tablet with Android or iOS and PC with Windows or macOS.

Safety Summary

...

Warning  
Do not store or carry flammable liquids, gases or explosive materials in the same compartment as the device, its parts or accessories.  

Warning  
If Blu-Link is attached to TITAN, incorrectly Incorrectly connecting positive and negative battery terminals will may cause immediate damage to the device or ETU, which is not covered by the warranty, and can lead to fire. 

Caution
Prevent the device from contact with conductive materials, such as dust, liquid or metal powder.

...

Notice
In case you have any difficulties while installing or using this product:
a) email us at support@gatee.eu
b) contact us via Facebook: https://www.facebook.com/gatee
c) call (+48) 122-100-523

 

How to use Blu-Link

(grafika z pudełka)

Plug and play

  1. Attach Plug Blu-Link to AEG battery top LED side up

  2. If LED glows green, go to the next step. If not, see Blu-Link Troubleshooting Card (included in the kit)

  3. Connect battery with attached Blu-Link to Plug AEG/ETU

  4. Place battery in the stock

  5. Enjoy using into Blu-Link

...

  1. Enjoy using Blu-Link

...

First connection via GCS

  1. Download and install GATE Control Station:
    www.gatee.eu/gcs

  2. Enable Bluetooth on your device (version 4.1 or later)Attach

  3. Plug Blu-Link to AEG battery top LED side up

  4. If LED glows green, go to the next step. If not, see Blu-Link Troubleshooting Card (included in the kit)

  5. Log in to the GCS app

  6. Prepare PIN printed on Blu-Link box*card

  7. Connect Blu-Link by following instructions displayed in GCSConnect battery with

  8. attached Blu-Link to the Plug AEG/ETU

  9. Place battery in the stock

  10. Enjoy using into Blu-Link

...

  1. Enjoy using Blu-Link

...

Notice
Keep Blu-Link box or save PIN printed on it – you will need it in case the device is damaged, lost or stolen.

Notice
Blu-link is compatible with Bluetooth version 4.1 or later

Troubleshooting

Notice
Blu-Link troubleshooting during its connection is described on Troubleshooting Card included in the kit.

...

[grafika - flaga w kolorze i z liczba plus strzałki wyjasniające]

Notice
If you are using ETU connected with Blu-link and problem occure, check also its DTC in GCS app.

LED

WHAT HAPPENED

POSSIBLE REASON

WHAT TO DO

UVP1
Protection against over - discharge of the battery. Battery protection was activated.

The battery is discharged

Charge the battery

UVP2
- The voltage dropped below ??? V 1.9 V which is critical for Blu-Link to work properly.

a) If you have TITAN or ASTER, check its DTC in GCS app.

b) For other ETUs – verify what happened or Otherwise, diagnose your ETU1. The battery is discharged

2. The battery is worn out and has too high internal resistance

3. Inadequate battery type for given AEG configuration

4. Too much electrical resistance between Blu-Link and the battery

5. Motor too strong for the connected battery

6. Motor connections short circuit

7. Motor is jammed

8. Motor is damaged

  1. Charge the battery\

  2. Replace the battery

  3. Use a battery with more capacity or more voltage

  4. Do not use any adapters

  5. Use standard or high-torque motors instead of high-speed

  6. Check and fix the motor wires insulation

  7. Unjam the motor

  8. Replace the motor

 

UVP3
- Protection against over-discharge of the battery. Battery protection was activated immediately after connecting the battery.

a) If you have TITAN or ASTER, check its DTC in GCS app.

b) For other ETUs – verify what happened or Otherwise, diagnose your ETU

  1. Number of cells is different than their number set in GCS

  2. The battery is discharged

  1. Set the same number of cells in GCS as in the battery

  2. Charge the battery

OVL
- Too high load.

The load limit was exceeded.?

??Use high-torque motor and gears

OCP
- Blu-Link detected too high current.  Over current Overcurrent protection was activated.

a) If you have TITAN or ASTER, check its DTC in GCS app.

b) For other ETUs – verify what happened or Otherwise, diagnose your ETU

Image Removed

SCP

  1. Too low current is set in smart fuse settings

  2. Motor is damaged

  3. Motor or gearbox is jammed

  4. Motor connections short circuit

  1. Adjust smart fuse settings

  2. Replace the motor

  3. Unjam the motor or gearbox

  4. Check and fix the motor wires insulation

Image Added

SCP - Blu-Link detected current over 240 A ???. Short circuit protection was activated.

a) If you have TITAN or ASTER, check its DTC in GCS app.

b) For other ETUs – verify what happened or Otherwise, diagnose your ETU

  1. Motor is damaged

  2. Motor or gearbox is jammed

  3. Motor connections short circuit

  1. Replace the motor

  2. Unjam the motor or gearbox

  3. Check and fix the motor wires insulation

OTP
- Blu-Link temperature is too high. Over temperature protection was activated.

OTP

  1. Outside temperature is too high in correlation with the demanding AEG

  2. Frequent short circuits and Blu-Link electrical overloads

Wait until the temperature drops

...