Content Comparison

Congratulations on your Blu-Link!

...

For your safety, read the safety information below carefully before installing the device.

...

Warning  
Do not store or carry flammable liquids, gases or explosive materials  gases or explosives in the same compartment as the device, its parts or accessories.  

...

Caution
Connecting battery with voltage over 17 V will cause permanent damage to Blu-Linkthe device, which is not covered by the warranty.

...

Notice
You can use Blu-Link without ETU. It will work as a smart fuse and wattmeter enabling to e.g. read telemetry data.

...

1. Download and install GATE Control Station:
   www.gatee.eu/gcs

2. Enable Bluetooth function on your device

3. Prepare Blu-Link DTC card included in the kit

4. Plug Blu-Link into AEG battery LED side up. LED should glow green for 1 seconds.

5. Read LED status and compare it with DTC card

6. Log in to the GCS app

7. Prepare PIN printed on Blu-Link’s PIN card

8. Connect Blu-Link by following instructions displayed in GCS

9. Plug AEG/ETU into Blu-Link

10. Enjoy using Blu-Link

...

Notice
Keep the Blu-Link’s PIN card or save PIN printed on it – you will need it for each new connection. If you lose your PIN, contact us at : support@gatee.eu.

Notice
Blu-link is compatible with Bluetooth version 4.0 or later.

...

Diagnostic Trouble Codes (DTC) inform about basic malfunctions and problems with your battery, AEG, ETU or Blu-Link. You are notified of them by LED blinking for 2 minutes since after the problem occurs. The Blu-Link’s DTC can be later read and cleared in DTC menu in GCS app.

...

How to read DTC explanations

• grafika - flaga w kolorze i z liczba plus strzałki wyjaśniające

• dodać za liczbą mignięć znak “x” np. 2x

• przemyśleć bardziej obrazowe oznaczanie liczby mignięć, np. warfet, 4 błyśnięcia:

  

Notice
If you use an ETU connected to Blu-Link, check also the ETU's DTC. The Blu-Link is designed to withstand higher power load and lower voltage than an ETU, so in most cases, an ETU protection turns on earlier and the Blu-Link doesn’t notice the problem.

LED	WHAT HAPPENED	POSSIBLE REASON	WHAT TO DO
	OVL – The load limit was exceeded.	Too high load	Contact us at support@gatee.eu
	OCP – Blu-Link detected too high current. Overcurrent protection was activated.	Too low current is set in smart fuse settings Motor is damaged Motor or gearbox is jammed Motor connections' short circuit	Adjust smart fuse settings Replace the motor Unjam the motor or gearbox Check and fix the motor wires' insulation
	SCP – Blu-Link detected current over >270 A. Short circuit protection was activated.	Motor is damaged Motor or gearbox is jammed Motor connections' short circuit	Replace the motor Unjam the motor or gearbox Check and fix the motor wires' insulation
	OTP – Blu-Link temperature is too high. Over temperature protection was activated.	Outside temperature is too high in correlation with the demanding AEG Frequent short circuits and Blu-Link’s electrical overloads	Wait until the temperature drops.
	UVP1 – Battery protection was activated.	The battery is discharged	Charge the battery
	UVP2 – The voltage dropped below 1.5 V which is critical for Blu-Link to work properly.	1. The battery is discharged 2. The battery is worn out and has too high internal resistance 3. Inadequate battery type for given AEG configuration 4. Too much electrical resistance between Blu-Link and the battery 5. Motor too strong for the connected battery 6. Motor connections' short circuit 7. Motor is jammed 8. Motor is damaged	Charge the battery Replace the battery Use a battery with more capacity or more voltage Do not use any adapters Use standard or high-torque motors instead of high-speed ones Check and fix the motor wires insulation Unjam the motor Replace the motor
	UVP3 – Protection against over-discharge of the battery. Battery protection was activated immediately after connecting the battery.	Number of cells is different than their number set in GCS The battery is discharged	Set the same number of cells in GCS as in the battery Charge the battery

...