Content Comparison

Congratulation on your new Blu-Link!

...

Notice
You can use Blu-Link without ETU. It will work as a smart fuse and power analyzer enabling to, e.g., read telemetry data.

...

1. Download and install GATE Control Station:
   www.gatee.eu/gcs

2. Enable Bluetooth function on your device

3. Prepare Blu-Link DTC card included in the kit

4. Plug Blu-Link into AEG battery LED side up. LED should glow green for 1 s.

5. Read the LED status and relate to DTC card

6. Log in to into the GCS app

7. Prepare PIN printed on the Blu-Link’s Link PIN card

8. Connect Blu-Link by following the instructions displayed in from the GCS

9. Plug Blu-Link into AEG/ETU

10. Enjoy using of the Blu-Link

Plug and play

1. Plug Blu-Link into AEG battery

2. Plug Blu-Link into AEG/ETU

3. Enjoy the airsofting

Notice
Keep the Blu-Link’s Link PIN card or save PIN printed on it – you will need it for each new connection. If you lose your PIN, contact us at support@gatee.eu.

...

Notice
Blu-link is compatible with the Bluetooth version 4.0 or later.

...

In the event of trouble

1. The colour of LED serves to reflect reflects on the actual issue, whereby respectivelyproblem type:

   1. Yellow to indicate indicates a warning

   2. Red to indicate indicates a critical problem

2. Number of blinks determines what exactly the problem is (for reference, read DTC explanations presented later on in this guide) / The actual nature of the issue will be said corroborated by the number of blinks (for reference, please acquaint the explications from the DTC, to be available further on across this guidebook)

...

DTC explanations

• grafika - flaga w kolorze i z liczba plus strzałki wyjaśniające

• dodać za liczbą mignięć znak “x” np. 2x

• przemyśleć bardziej obrazowe oznaczanie liczby mignięć, np. warfet, 4 błyśnięcia:

  

Notice
If you use an ETU connected to Blu-Link, check also the ETU's DTC. Blu-Link is designed to withstand higher power load and lower voltage than ETU, so in most cases, an ETU protection turns on earlier and the Blu-Link does not detect the problem.

/ If ETU used in connection to Blu-Link, the DTC to be also checked for the ETU. Since the Blu-link is so-designed to be up to withstand a higher power and lower voltage from the ETU, in most cases by the moment of a possible clash was detected, the ETU protection will have been turned on automatically, so that the Blu-Link was enabled to ignore the problem as unrecognized whatsoever and take for no action to address of it thereby.

LED	WHAT HAPPENED	POSSIBLE REASON	WHAT TO DO
	OVL – The load limit was exceeded.	Too high load	Contact us at support@gatee.eu
	OCP – Blu-Link has detected a too high current. Overcurrent The overcurrent protection was has been activated.	Too low current is set in the smart fuse settings Motor is damaged Motor or gearbox is jammed Motor connections ' short circuit	Adjust smart fuse settings Replace the motor Unjam the motor or gearbox Check and fix the motor wires ' insulation
	SCP – Blu-Link detected a current over 270 A. Short The short circuit protection was activated.	Motor is damaged Motor or gearbox is jammed Motor connections ' short circuit	Replace the motor Unjam the motor or gearbox Check and fix the motor wires ' insulation
	OTP – Blu-Link temperature is too high. Over temperature protection was activated.	Outside temperature is too high in correlation with the demanding AEG Frequent short circuits and Blu-Link’s Link electrical overloads	Wait until the temperature drops
	UVP1 – Battery protection was has been activated.	The battery is discharged	Charge the battery
	UVP2 – The voltage dropped below 1.5 V, which is critical for Blu-Link to work properly.	1. The battery is discharged 2. The battery is worn out and has too high internal resistance 3. Inadequate battery type for given AEG configuration 4. Too much electrical resistance between Blu-Link and the battery 5. Motor too strong powerful for the battery connected battery 6. Motor connections ' short circuit 7. Motor is jammed 8. Motor is damaged	Charge the battery Replace the battery Use a battery with more of a greater capacity or more voltage Do not use any adapters Use standard or high-torque motors instead of high-speed ones Check and fix the motor wires insulation Unjam the motor Replace the motor
	UVP3 – Protection against over-discharge of the battery. Battery protection was activated immediately after connecting the battery was connected.	Number of cells is different than their differs from the number set in the GCS The battery is discharged	Set the same number of cells in GCS as in the battery Charge the battery up

Notice
There may be several codes displayed one after another, e.g., SCP and UVP2: 4 red blinks; 2 yellow blinks.

...

Bluetooth Trademark Attribution (może być małą czcionką, jak przypis)

The Bluetooth® by both, the word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by GATE Enterprise sp. z o.o. sp. k. is under license. Other trademarks and trade names are those of their respective owners.

...

This device complies with Part 15 of the FCC [Federal Communications Commission] Rules. Operation is subject to the following two conditions; (1) this device may not cause a harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

...

Please read this Legal Notice before operating your device and keep it for future reference.
This document contains important terms and conditions with respect to your device. By using of this device, you accept those terms and conditions.

...