Congratulation on your new Blu-Link!

...

Together with the GCS, you can adjust TITAN or ASTER settings and update or upgrade their firmware from devices with Android, iOS and since fall 2020, also Windows or macOS.

Safety Summary

...

1. Download and install GATE Control Station:
   www.gatee.eu/gcs

2. Enable Bluetooth function on your device

3. Prepare Blu-Link DTC card included in the kit

4. Plug Blu-Link into AEG battery, LED side up. LED should glow green for 1 s.

5. Read the LED status and relate to DTC card

6. Log into the GCS app

7. Prepare PIN printed on the Blu-Link PIN card

8. Connect Blu-Link by following the instructions from the GCS

9. Plug Blu-Link into AEG/ETU

10. Enjoy using of the Blu-Link

...

1. The color of LED reflects on the problem type:

   1. Yellow indicates a warning

   2. Red indicates a critical problem

2. Number of blinks determines what exactly the problem is (for reference, read DTC explanations presented later on in this guide)

DTC explanations

• grafika - flaga w kolorze i z liczba plus strzałki wyjaśniające

• dodać za liczbą mignięć znak “x” np. 2x

• przemyśleć bardziej obrazowe oznaczanie liczby mignięć, np. warfet, 4 błyśnięcia:

  

Notice
If you use an ETU connected to Blu-Link, check also the ETU DTC. Blu-Link is designed to withstand higher power load and lower voltage than ETU, so in most cases, the ETU protection turns on earlier and the Blu-Link does not detect the problem.

LED	WHAT HAPPENED	POSSIBLE REASON	WHAT TO DO
	ULL – Blu-Link has detected a too high load.	User load limit was exceeded.	Modify adjustable smart fuse settings. Contact us at support@gatee.eu
	OCP – Blu-Link has detected a too high current. The overcurrent protection was activated.	Motor is damaged. Motor or gearbox is jammed. Motor connections short circuit.	Replace the motor. Unjam the motor or gearbox. Check and fix the motor wires insulation.
	SCP – Blu-Link has detected a current over 270A. The short circuit protection was activated.	Motor is damaged. Motor or gearbox is jammed. Motor connections short circuit.	Replace the motor. Unjam the motor or gearbox. Check and fix the motor wires insulation.
	OTP – Blu-Link temperature is too high. Over temperature protection was activated.	Outside temperature is too high in correlation with the demanding AEG. Frequent short circuits and Blu-Link electrical overloads.	Wait until the temperature drops.
	UVP1 – Battery protection was activated.	The battery is discharged.	Charge the battery.
	UVP2 – The voltage dropped below level critical for Blu-Link to work properly.	1. The battery is discharged. 2. The battery is worn out and has too high internal resistance. 3. Inadequate battery type for given AEG configuration. 4. Too much electrical resistance between Blu-Link and the battery. 5. Motor is too powerful for the battery connected. 6. Motor connections short circuit. 7. Motor is jammed. 8. Motor is damaged.	Charge the battery. Replace the battery. Use a battery of a greater capacity or voltage. Do not use any adapters. Use standard or high-torque motors instead of high-speed ones. Check and fix the motor wires insulation. Unjam the motor. Replace the motor.
	UVP3 – Protection against over-discharge of the battery. Battery protection activated immediately after the battery was connected.	Number of cells differs from the number set in the GCS. The battery is discharged.	Set the same number of cells in GCS as in the battery. Charge the battery up.

Notice
There may be several codes displayed one after another, e.g., SCP and UVP2: 4 red blinks; , 2 yellow blinks.

Notice
It is a good practice to clear the DTC in GCS before each skirmish.

...

Bluetooth Trademark Attribution (może być małą czcionką, jak przypis)

The Bluetooth® by both, the word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by GATE Enterprise sp. z o.o. sp. k. is under licensesubject to licensing. Other trademarks and trade names are those of their respective owners.

...

1. This Limited Warranty is valid provided that the owner provides a proof of purchase and a properly completed warranty form.

2. This Limited Warranty does not cover: (a) defects or damage (e.g., mechanical, thermal or chemical) resulting from accident, misuse (misinterpretation of the instructions), abuse, neglect, unusual physical, electrical or electromechanical stress, water immersion, repairs or structural modification of any part of the product, or (b) the product that has its serial number removed or made illegible; (c) defects or damage from improper operation, maintenance or installation, ; (d) installation of the products.

3. Requests for warranty are processed as soon as possible, not exceeding seven (7) working days. The company’s obligation under this Limited Warranty shall be limited to providing replacement of part(s) only.

...