| Table of Contents | ||||
|---|---|---|---|---|
|
v4.
...
1-
...
05 [
...
2024-
...
07-
...
10]
...
| Code Block | |
|---|---|
| |
| |
Improved:
- trigger sensor functionality
- selector mode configuration in Programming via Trigger changed from SAFE-BINARY-SEMI to SAFE-SEMI-BINARY
- Programming via Trigger card available in https://help.gatee.eu/
Added:
- brushless motor support
- brushless motor configuration without connecting to GCS
- trigger sensitivity regulation without connecting to GCS
- Pre-cocking Boost configuration without connecting to GCS
- full access to Telemetry data previously available only with EXPERT firmware
- service mode that allows you to check the operation of the gear sensor during installation without using GCS
- Magazine Capacity: 115 BBs
- Reload time: 0.5 s
- Low ammo warning: 10 BBs
- Sniper delay: 0.2 s/0.5 s
- Cycle detection: Manual |
ADVANCED
| Code Block |
|---|
Improved:
- trigger sensor functionality
- selector mode configuration in Programming via Trigger changed from SAFE-BINARY-SEMI to SAFE-SEMI-BINARY
- Programming via Trigger card available in https://help.gatee.eu/
Added:
- brushless motor support
- brushless motor configuration without connecting to GCS
- trigger sensitivity regulation without connecting to GCS
- Pre-cocking Boost configuration without connecting to GCS
- full access to Telemetry data previously available only with EXPERT firmware
- service mode that allows you to check the operation of the gear sensor during installation without using GCS
- Low ammo warning: 20 BBs
- ROF Control: Adaptive: 1/2/3/...100 RPS
- Cycle detection: Manual |
sensor diagnostics mode removed
Added:
- Support for M4 replicas, with selector fire modes spaced every 45 degrees |
v4.1-04 [2024-04-25]
| Code Block | ||
|---|---|---|
| ||
Improved:
- UVP1 protection operation
- 2-stage trigger
- SEMI mode operation with BLDC motors
- ROF Adaptive operation
- removed showing and clearing DTCs in the Programming via Trigger menu. The ADVANCED function now includes options for:
1. restoring default settings
2. restoring factory settings
3. setting trigger sensitivity with the ability to check the currently set sensitivity
Added:
- DECOCKING
- full adjustment of Active Break (0-100%) even when Pre-Cocking is enabled |
v4.1-01 [2024-02-22]
| Code Block | ||
|---|---|---|
| ||
Improved:
- notification of the gear cam condition communicated to GCS |
v4.0-03 [2023-07-21]
| Code Block | ||
|---|---|---|
| ||
Improved:
- functioning of selector calibration for GCS and for calibration mode (available after restoring factory settings)
- ROF Control functioning of the following types: Manual Delay and Adaptive
- Magazine Mode functioning |
v4.0-02 [2023-07-07]
| Code Block | ||
|---|---|---|
| ||
Improved:
- cycle control
- Pre-Cocking mode
- BINARY mode when Sniper Delay mode is enabled
Added:
- setting any brake force value in Brushless mode
- setting any brake force value in BASIC firmware
- a new diagnostic mode for the gear sensor, trigger, and selector; the diagnostic mode is available when the system is installed in the gearbox |
v4.0-01 [2022-08-24]
BASIC, ADVANCED and EXPERT
| Code Block |
|---|
Improved: - trigger sensor functionality -SAFE / SEMI / BINARY instead of SAFE / BINARY / AUTO selector mode configuration- intrigger Programmingsensor viafunctionality: Triggernew changednoise-resistant from SAFE-BINARY-SEMI to SAFE-SEMI-BINARY -trigger detection algorithm - new Programming via Trigger card available inat https://help.gatee.eu/aster-se-qs Added: - brushless motor support - brushless motor modeconfiguration available without connecting to GCS - trigger sensitivity adjustment without connecting to GCS - Prepre-cocking Boostboost configurationadjustment without connecting to GCS - automatic pre-cocking: LOW / MID / HIGH - service mode that allows you to check the operation of the gear sensor during installation without using GCS |
BASIC
| Code Block |
|---|
Added:
- new Magazine Capacity option: 115 BBs
- new Reload time option: 0.5 s
- new Low ammo warning option: 10 BBs
- new Sniper delay option: 0.2 s/0.5 s
- new Cycle detection mode: Manual |
ADVANCED
| Code Block |
|---|
Added:
- new Low ammo warning option: 20 BBs
- new Adaptive ROF Control mode: 1/2/3/...100 RPS
- new Cycle detection mode: Manual |
...
v3.5-02 [2021-08-09]
| Code Block |
|---|
Added: - communication with STATUS Removed: - Programming via Trigger Improved: - sending selector state to STATUS |
...
| Code Block |
|---|
Improved: - Operation of the trigger - Detecting of 2-cell battery - Removing of blockade after trigger sensor was overexposed - First shot failure after switching fire selector from SAFE - 2-stage trigger operation for Quantum Trigger - Fire selector operation at high ambient temperatures - DTC error tracking if the trigger and/or selector - Gear sensor support for GCS Other improvements Fixed: - Elimination of a shot while switching from SAFE to SEMI when Quantum Trigger is pressed Added: - Support for BLDC motors - Support for GATE Quantum Trigger™ - Green LED blinks after connecting the battery if self test was passed successfully |
...