| Table of Contents | ||||
|---|---|---|---|---|
|
v4.1-05 [2024-07-10]
| Code Block | ||
|---|---|---|
| ||
Improved:
- sensor diagnostics mode removed
Added:
- Support for M4 replicas, with selector fire modes spaced every 45 degrees |
v4.1-04 [2024-04-25]
| Code Block | ||
|---|---|---|
| ||
Improved:
- UVP1 protection operation
- 2-stage trigger
- SEMI mode operation with BLDC motors
- ROF Adaptive operation
- removed showing and clearing DTCs in the Programming via Trigger menu. The ADVANCED function now includes options for:
1. restoring default settings
2. restoring factory settings
3. setting trigger sensitivity with the ability to check the currently set sensitivity
Added:
- DECOCKING
- full adjustment of Active Break (0-100%) even when Pre-Cocking is enabled |
v4.1-01 [2024-02-22]
| Code Block | ||
|---|---|---|
| ||
Improved:
- notification of the gear cam condition communicated to GCS |
v4.0-03 [2023-07-21]
| Code Block | ||
|---|---|---|
| ||
Improved:
- functioning of selector calibration for GCS and for calibration mode (available after restoring factory settings)
- ROF Control functioning of the following types: Manual Delay and Adaptive
- Magazine Mode functioning |
v4.0-02 [2023-07-07]
| Code Block | ||
|---|---|---|
| ||
Improved:
- cycle control
- Pre-Cocking mode
- BINARY mode when Sniper Delay mode is enabled
Added:
- setting any brake force value in Brushless mode
- setting any brake force value in BASIC firmware
- a new diagnostic mode for the gear sensor, trigger, and selector; the diagnostic mode is available when the system is installed in the gearbox |
v4.0-01 [2022-08-24]
BASIC, ADVANCED and EXPERT
| Code Block |
|---|
Improved: |
...
- SAFE / SEMI / BINARY instead of SAFE / BINARY / AUTO selector mode |
...
- trigger sensor functionality: new noise-resistant trigger detection algorithm |
...
- new Programming via Trigger card available at https:// |
...
gatee.eu/ |
...
aster-se-qs Added: |
...
- brushless motor support |
...
- brushless motor configuration without connecting to GCS |
...
- trigger sensitivity adjustment without connecting to GCS |
...
- pre-cocking boost adjustment without connecting to |
...
GCS - automatic pre-cocking: LOW / MID / HIGH |
...
- service mode that allows you to check the operation of the gear sensor during installation without using GCS |
BASIC
| Code Block |
|---|
Added: |
...
- new Magazine Capacity option: 115 BBs |
...
- new Reload time option: 0.5 s |
...
- new Low ammo warning option: 10 BBs |
...
- new Sniper delay option: 0.2 s/0.5 s |
...
- new Cycle detection mode: Manual |
ADVANCED
| Code Block |
|---|
Added: |
...
- new Low ammo warning option: 20 BBs |
...
- new Adaptive ROF Control mode: 1/2/3/...100 RPS |
...
- new Cycle detection mode: Manual |
...
v3.5-02 [2021-08-09]
| Code Block |
|---|
Added: - communication with STATUS Removed: - Programming via Trigger Improved: - sending selector state to STATUS |
...
| Code Block |
|---|
Improved: - Operation of the trigger - Detecting of 2-cell battery - Removing of blockade after trigger sensor was overexposed - First shot failure after switching fire selector from SAFE - 2-stage trigger operation for Quantum Trigger - Fire selector operation at high ambient temperatures - DTC error tracking if the trigger and/or selector - Gear sensor support for GCS Other improvements Fixed: - Elimination of a shot while switching from SAFE to SEMI when Quantum Trigger is pressed Added: - Support for BLDC motors - Support for GATE Quantum Trigger™ - Green LED blinks after connecting the battery if self test was passed successfully |
...