The most common mistakes:
1. Washer
...
Issue
User's fault:
...
placing washers in wrong order
...
Result:
...
short circuit and permanent damage to
...
TITAN
...
How to detect
...
:
Correct order:
...
2. Trigger sensors damageSensor Damage
User's fault:
...
pulling the trigger when the gearbox is open
...
Result:
...
torn off trigger sensors
...
TITAN will not be able to detect all 5 trigger sensitivities even
...
if using a standard trigger (please note that in the case of speed triggers TITAN
...
cannot detect all trigger sensitivities
...
either, which does not mean that sensors are damaged).
How to detect
...
: missing trigger sensors (receivers)
...
...
...
3.
...
Cable Damage
User's fault:
...
incorrect cable routing
...
Result:
...
damaged or torn off wires by motor gear
How to detect
...
: damaged
...
insulation
...
4. Capacitor
...
Damage
User's fault:
...
mounting TITAN V2 in an ICS gearbox without necessary modifications
Result:
...
the gearbox latch has damaged or torn the yellow capacitor
How to detect
...
: yellow capacitor is missing or damaged
...
5. Gear
...
Sensor Damage
User's fault:
...
very low
...
sector gear shimming
Result:
...
torn off gear sensor
...
How to detect
...
: missing gear sensor
...
Less frequently encountered:
6.
...
Fire Selector Sensor Damage
User's fault:
...
incorrect bottom board placement in gearbox shell
Result:
...
torn off
...
Fire Selector sensor
...
How to detect
...
: one of the trigger sensors
...
missing
7. Motor connector damage
User's fault:
...
using too much force during motor connector bending, bending
...
connectors wrong
...
way
...
Result:
...
broken motor connector
How to detect
...
: motor connector
...
broken in half
8.
...
Reverse polarity
User's fault:
...
plugging a battery
...
into the unit in incorrect order (a negative wire with a positive wire and a positive wire with a negative wire)
Result:
...
destroying the main parts of the board
How to detect
...
: theunit is not responding,
...
the entire board is
...
burnt
...
9. Wire
...
Damage (
...
Caused by
...
Trigger)
User's fault:
...
incorrect wire placement in gearbox shell
Result:
...
torn wire insulation
How to detect
...
: tornwire insulation close to the trigger
10.
...
Short Circuit Caused by Damaging Cable Insulation
User's fault:
...
accidentallycutting both positive and negative
...
wires with the body of the replica
Result: Insulation damage, short circuit
How to detect
...
: visibly cut wires
11. Repairs or
...
Structural Modification of any TITAN
...
Part (including rewiring and component replacement)
User's fault:
...
interference in the
...
structure of the unit
Result:
...
automatic warranty loss
...
How to detect
...
: visible changes such as different wire color
...
Cases when warranty should be accepted:
...
Other Cases When Warranty May Be Accepted:
Recurring E01 to E06
and, E13, E14, and E15 errors
- Total absence of
No reaction whatsoever from the unit without visible damage
No connection with
theUSB-Link and/or
programming cardTactical Programming Card even if the unit is working properly without any visible damage (no programming option)
- Continuous occurrence
Recurrence of error E07 combined with no cycle detection (after
very accuratedetailed troubleshooting)
| Info |
|---|
In case of any doubts please contact oursupportSupport at:support@gatee
tel. +48 12 210 05 23 |
Related articles
| Filter by label (Content by label) | ||||||||||
|---|---|---|---|---|---|---|---|---|---|---|
|
...
|
| Page Properties | ||
|---|---|---|
| ||
|