Initial Use
Before inserting TITAN into the gearbox, connect TITAN to GCS via Blu-Link or USB-Link. You can download GCS here: https://www.gatee.eu/gcs
The GCS Information for Use is here: https://www.gatee.eu/manuals
Check for latest firmware updates.
Now you’re ready to install TITAN in the gearbox.
Installation
Caution
Regardless of your previous experience, follow all safety precautions to prevent any damage to your TITAN.
Caution
TITAN installation requires deep technical knowledge of gearbox internals. To avoid damage, we recommend it to be installed by a skilled person. If, however, you wish to proceed with TITAN installation on your own, you must watch the installation video and read the full-length PDF manual: https://www.gatee.eu/manuals beforehand. Incorrect installation may result in amongst others sensor damage, which is not covered by warranty.
Note
TITAN V2 and TITAN V3 do not support Infinite torque-up gears.
Note
Apply a thin layer of grease. Excessive grease may cover sensors or gaps between teeth, which will result in cycle detection issues. Use grease of appropriate viscosity and density to avoid splashing.
Note
In the GCS App configure the gear type (if your gears are not stock) and perform first-time sensor calibration for TITAN V3 and TITAN V2 NGRS.
Note
In case of any difficulties installing or using this product:
email us at support@gatee.eu;
contact us via Facebook: https://www.facebook.com/gatee;
call us on (+48) 12 210 05 23.
TITAN V2
Caution
A sector gear can damage the gear sensor during installation. Avoid this damage.
Caution
An insulation washer is required. Placing washers in the wrong order will cause a short circuit and permanent damage to TITAN, which is not covered by warranty.
Caution
Incorrect placement of wiring under the motor gear may cause insulation damage and a short circuit, which is not covered by warranty.
Caution
ICS gearboxes require modification to avoid TITAN damage.
Caution
Do not pull the trigger when the gearbox is open. This may result in trigger sensor damage.
Note
In the case of some triggers (e.g. speed or CNC triggers), the first trigger sensor(s) may be covered even when the trigger is not pulled, which is due to its design.
Note
The fire selector sensor does not detect black surface. If the fire selector does not come with a metal connector or it does not work properly, you must use an appropriate sticker from the kit.
Note
Sticker position is crucial. Make sure to align it exactly to the left edge and the top red line.
The set contains 3 different sticker types. First, use the one with the thinner black line. If you are not able to calibrate the selector, try the other ones.
Caution
In TITAN V2 connectors must be bent according to the photo below. Bending connectors in the opposite direction may break them. If this should happen, spare terminals are included in the installation kit.
TITAN V3
Note
TITAN V3 fits CNC gearboxes with very low backlash. While fitting TITAN, pull the cables and at the same time push the board into the right place. Pay attention to the area marked yellow to fit the board correctly.
Caution
Use a metal washer with a max. 8 mm [0.31 in] diameter to avoid TITAN damage.
Note
Use the trigger sticker to make it visible for the trigger sensor.
*grafika*
Note
TITAN can detect trigger position very precisely. In order to use it, you need to eliminate trigger backlash. The set contains 3 trigger anti-backlash stickers of various thicknesses. Try each one of them and choose the most appropriate one.
*grafika*
Note
The selector plate requires modification. Place the selector sticker according to the photos below. Its position is crucial.
*grafika łącząca dwie dotychczasowe*
Caution
In TITAN V3 the connectors should be straight according to the photo below. Bending and straightening the connectors back may cause them to break. If this happens, spare terminals are included in the installation kit.
TITAN V2 NGRS
Warning
If you are using a recoil system and set excessive trigger sensitivity, it may cause accidental discharge even without pressing the trigger.
*grafika*
Warning
Pay attention to correctly solder positive and negative TITAN wires to the connector. Incorrectly connecting positive and negative battery terminals will cause immediate damage to the device, which is not covered by warranty, and can lead to fire.
*grafika*
Caution
An insulation washer is required. Placing washers in the wrong order may cause a short circuit and permanent damage to TITAN, which is not covered by warranty.
podobna grafika co w przypadku NGRS czy V2*
Caution
Do not locate the screw in the cut-off lever hole to secure the TITAN board. Use a contact block mounting screw in the hole indicated by the arrow.
*grafika*
Caution
Incorrect placement of wiring under the motor gear may cause insulation damage and a short circuit, which is not covered by warranty.
*grafika*
Caution
In order to secure the wires properly, modify the gearbox as shown in the photos below.
*grafika*
Note
The selector plate requires modification. Place the selector sticker according to the photos below. Its position is crucial.
*grafika*
Caution
In TITAN NGRS connectors should be bent according to the photo below. Bending connectors in the opposite direction may cause them to break. If this happens, spare terminals are included in the installation kit.
Quick Access Men
Instructions
Powiązane artykuły
Filter by label
There are no items with the selected labels at this time.