Changelog
Data publikacji w GHC | Wersja GHC | Lokalizacja w GHC | Kto zatwierdził | |
|---|---|---|---|---|
| 1 |
|
|
| |
| 2 |
|
|
|
|
General Information
The information contained in this document is subject to change without notice.
Read carefully before use. Keep for future reference.
Failing to read this information may void the guarantee!
When using the product, always follow basic safety rules to reduce the risk of injury from fire or electrical shock.
Safety Summary
Please read this to ensure safe and correct use. Retain this information for future reference. The information contained in this document is subject to update without notice.
For your safety, this product should be installed by a skilled person.
Warning
Situations that may cause injury to yourself or others.
Caution
Situations that may cause damage to your device or other equipment.
Note
Notes, usage tips or additional information.
Warning
This device is not a toy and may not be operated by people (including children) with limited physical or mental abilities, as well as by people with no earlier experience in operation of electronic equipment. They may use the device only under the supervision of people responsible for their safety.
Warning
Before starting the installation process, make sure that your AEG magazine is empty and there are no BBs inside.
Warning
This equipment is not suitable for use in locations where children are likely to be present.
Warning
Persons under 18 years of age ought not stay unattended near the device during the installation or servicing of a device installed in an ASG replica.
Warning
Persons under 18 years of age ought not stay unattended near the device installed in an ASG replica ready for use.
Warning
Persons under 18 years of age are not allowed to install or commission the device in an ASG replica.
Warning
Persons under 18 years of age are not allowed to service this device.
Warning
Do not store or carry flammable liquids, gases or explosive materials in the same compartment as the device, its parts or accessories.
Warning
Incorrectly connecting positive and negative battery terminals will cause immediate damage to the device, which is not covered by warranty, and can lead to fire.
Warning
Take caution to prevent short-circuiting the battery as the consequences may be very dangerous.
Warning
Excessive trigger sensitivity may cause unintentional discharge (firing).
Warning
When an airsoft replica is not in use, its battery must be disconnected and the hop-up chamber must be empty.
Warning
While handling an AEG replica with a connected battery, anyone within the range of the replica must wear personal protective equipment.
Warning
When not in SAFE mode, avoid using the device around strong electromagnetic fields, such as PMR transmitters exceeding European standards or when electrostatic discharges, e.g. lightning, occur in the atmosphere, which may cause malfunction of the device and unintentional discharge (firing).
Warning
When an airsoft gun is not in use, its magazine must be detached or kept empty with no BBs inside.
Caution
Do not remove the device protective film or heat shrink tubes. Removing them will void the warranty.
Caution
Do not swap TITAN PCB boards between different sets. The serial numbers of each board must match. Mixing boards can cause incorrect measurements of voltage and current, which affects the smart fuse and can lead to device damage not covered by warranty.
Caution
For your own safety you ought to use an additional fuse between the battery and the device.
Caution
When operating under unusual conditions, perform maintenance outlined below for the climate similar to your area. Operating in extremely cold temperatures is not recommended. Do not expose TITAN to direct sunlight for long periods of time. Keep away from dust or sand, which can cause malfunctions and/or excessive wear. Keep TITAN out of snow, rain, and water. This will prevent electrical failure and fluid buildup inside the gearbox.
Note
The product Warranty Form is available here: http://www.gatee.eu/warranty.
Installation
Caution
Regardless of your previous experience, follow all safety precautions to prevent any damage to your TITAN.
Caution
TITAN installation requires deep technical knowledge of gearbox internals. To avoid damage, we recommend it to be installed by a skilled person. If, however, you wish to proceed with TITAN installation on your own, you must read this full-length document and watch the installation video beforehand. Incorrect installation may result in, among others, sensor damage, which is not covered by warranty.
Note
TITAN V2 and TITAN V3 do not support infinite torque-up gears, only TITAN NGRS does.
Note
Apply a thin layer of grease. Excessive grease may cover sensors or gaps between teeth, which will result in cycle detection issues. Use grease of appropriate viscosity and density to avoid splashing.
Note
In GCS configure the gear type (if your gears are not stock) and perform first-time sensor calibration for TITAN V3 and TITAN V2 NGRS.
Note
In case you have any difficulties while installing or using this product:
contact us via https://help.gatee.eu
send us an e-mail: support@gatee.eu
TITAN V2
Caution
A sector gear can damage the gear sensor during installation. Avoid such damage.
Caution
An insulation washer is required. Place the washers according to the graphic below. Placing washers in the wrong order will cause a short circuit and permanent damage to TITAN, which is not covered by warranty.
Caution
Incorrect placement of wiring under the motor gear may cause insulation damage and a short circuit, which is not covered by warranty.
Caution
ICS gearboxes require modification to avoid TITAN damage.
Caution
Do not pull the trigger when the gearbox is open. This may result in trigger sensor damage.
Note
In some cases (e.g. speed or CNC triggers), the first trigger sensor(s) may be covered even when the trigger is not pulled, which is due to its design.
Note
The selector sensor does not detect black surface. If the selector does not come with a metal connector or is not working correctly, you must use an appropriate sticker from the INSTALLATION KIT.
Note
Sticker position is crucial. Make sure to align it exactly to the left edge and the top red line. The set contains 3 different sticker types. First, use the one with the thinner black line. If you are not able to calibrate the selector, try the other ones.
Caution
In TITAN V2 connectors must be bent according to the photo below. Bending connectors in the opposite direction may cause them to break. If this should happen, spare terminals are included in the INSTALLATION KIT.
TITAN V3
Note
TITAN V3 fits CNC gearboxes with very low backlash. While fitting TITAN, pull the cables and at the same time push the board into the right place. Pay attention to the area marked yellow to fit the board correctly. Do this carefully so as not to damage the insulation of the wires.
Caution
Use a metal washer with a diameter of max. 8 mm [0.31 inch] to avoid damaging TITAN.
Note
Use the trigger sticker to make it visible for the trigger sensor.
Note
TITAN can detect trigger position very precisely. In order to increase sensitivity, you need to eliminate trigger backlash. The set contains 3 trigger anti-backlash stickers of various thicknesses. Try each one of them or a combination of more than one and choose the most appropriate one.
Note
The selector plate requires modification. Place the selector sticker according to the photos below. Its position is crucial.
Caution
In TITAN V3 the connectors must be straight according to the photo below. Bending and straightening the connectors back may cause them to break. If this should happen, spare terminals are included in the INSTALLATION KIT.
TITAN V2 NGRS
Warning
If you are using a recoil system and set excessive trigger sensitivity, it may cause accidental discharge (firing) even without pressing the trigger.
Warning
Pay attention to correctly solder positive and negative TITAN wires to the connector. Incorrectly connecting positive and negative battery terminals will cause immediate damage to the device, which is not covered by warranty and can lead to fire.
Caution
An insulation washer is required. Place the washer(s) according to the graphic below. Placing washers in the wrong order will cause a short circuit and permanent damage to TITAN, which is not covered by warranty.
Caution
If the PCB does not perfectly fit in your shell, make the necessary modifications to the gearbox shell, not to the PCB.
It is forbidden to make any modifications to the PCB shell such as drilling the screw hole, grinding the edges of the PCB, etc. Doing so may result in immediate damage to the circuit, which is not covered by the warranty.
Caution
Do not locate the screw in the cut-off lever hole to secure the TITAN board. Use a contact block mounting screw in the hole indicated by the arrow.
Caution
Incorrect placement of wiring under the motor gear may cause insulation damage and a short circuit, which is not covered by warranty.
Caution
In order to secure the wires properly, modify the gearbox as shown in the photos below.
Note
The selector plate requires modification. Place the selector sticker according to the photos below. Its position is crucial.
Caution
In TITAN V2 NGRS connectors should be bent according to the photo below. Bending connectors in the opposite direction may cause them to break. If this should happen, spare terminals are included in the INSTALLATION KIT.
Quick Access Menu
You can access Pre-Cocking or Profiles using a shortcut. After firing a shot, burst or while in SAFE (only if the safety lever has been removed)*, hold the trigger and switch the selector within the specified time (see table). Switch the selector in any order to change between the options indicated by motor vibrations.
By releasing the trigger, you exit the function confirming it. Bear in mind that Programming via Trigger is a different process. To find out more check the PROGRAMMING VIA TRIGGER CARD included or continue reading below.
*You can enter Programming via Trigger only when the selector on the replica is in SEMI position and AUTO mode is not assigned to this position.
Pre-Cocking
In GCS go to Trigger>Pre-Cocking>Switch Mode via Selector and use the toggle button to activate this function.
Fire a shot, burst or pull the trigger while in SAFE mode (only if the safety lever has been removed) and do not release the trigger.
Switch the selector within 2 s. There is a single low frequency vibration.
Switch the selector in any order to change between the options indicated by vibrations:
1 low vibration – Pre-Cocking Off
2 low vibrations – Pre-Cocking Auto
3 low vibrations – Pre-Cocking Manual
Release the trigger to save the selected mode.
De-Cocking
Forcing the piston release after firing with Pre-Cocking enabled
Press the trigger in SEMI or BINARY mode and wait for the firing cycle to end – do not release the trigger.
After 1.5 s, a high, medium, high, medium, high, medium frequency audible message will be triggered.
Releasing the trigger after the sound message is equivalent to firing without Pre-Cocking. The piston remains in the rest position.
Note
Releasing the piston to the rest position does not mean that Pre-Cocking mode is deactivated. Each subsequent shot after pressing the trigger will be made with the piston cocked according to the selected Pre-Cocking mode.
Profile Selection
Profiles are sets of particular settings of configurable TITAN functions. You can choose one of the three profiles at a time. Go to General>Profiles>Change Profile via Selector in GCS to be able to use this function. If you want to change the active profile:
Fire a shot, burst or pull the trigger while in SAFE (only if the safety lever has been removed) and do not release the trigger.
Switch the selector within 2–7 s. There is a single high frequency vibration.
Switch the selector in any order to change between options, which are indicated by vibrations.
1 high frequency vibration – Profile 1
2 high frequency vibrations – Profile 2
3 high frequency vibrations – Profile 3
Release the trigger to save the selected profile.
Programming via USB-Link
Note
You can use a USB-Link to connect your TITAN to GCS for Android and Windows/macOS. To connect to GCS for iOS, you must use a Blu-Link.
Caution
Prevent the USB-Link and the ends of the USB cable from contact with conductive materials, such as dust, liquid or metal powder.
Caution
Do not remove the device heat shrink tube.
1. Connect the USB-Link via its Micro-USB plug to your PC, Mac or smartphone using one of the dedicated USB cables:
USB-A cable for PC/Mac
Micro-USB or USB-C cable for smartphones
Note
The micro-USB cable has the same connectors on both sides. However, it is very important to connect the USB-Link and smartphone to the appropriate ends of the cable as otherwise, it will not work.
Note
If your USB-Link cannot be detected, follow the instructions displayed in GCS.
2. Connect TITAN to the USB-Link.
Note
In case you have any difficulties while installing or using this product:
contact us via https://help.gatee.eu
send us an e-mail: support@gatee.eu
3. Now you can control TITAN via GCS.
USB-Link Troubleshooting
The USB-Link has a 4-color LED indicator.
Restoring Factory Settings
Note
Restoring the factory settings results in resetting the default settings, erasing adaptations and statistical data.
Note
Restoring the factory settings of TITAN V3 or TITAN NGRS requires re-calibration in GCS.
You can restore Factory Settings in 3 ways:
Via GCS:
Go to General. Open the menu in the upper right corner and select Restore factory settings.
Troubleshooting
Low Battery Warnings
When activated, you are warned 5 times before the battery is discharged. Each warning is communicated by 3 vibrations: High → Mid → High.
Vibrations after Connecting the Battery
TITAN can detect the number of battery cells automatically. If you activate this function, vibrations start once the battery is connected. Remember to always check if your TITAN detects the correct number of battery cells.
Diagnostic Trouble Codes
Diagnostic Trouble Codes (DTC) enable detecting basic malfunctions and problems with your AEG or TITAN. You are notified of the main errors by vibrations. DTCs can later be read and cleared in the DTC menu in GCS as well as in the Programming Mode in Advanced Settings.
If DTCs are read while in Programming Mode:
Each vibration type corresponds to an issue type
High frequency vibrations: warning
Low frequency vibrations: problem
Low-High frequency vibrations: device failed self-test
High-Low vibrations: another error
The number of vibrations determines exactly what the problem is (for reference read the DTC explanations presented later on in this guide)
Note
It is good practice to clear the DTCs in GCS before each skirmish.
TITAN V2
TITAN V2 has the following optical sensors:
1 sector gear sensor
2 selector sensors
5 trigger sensors
Installation
Please read the installation guide below before proceeding.
INSTALLATION KIT Contents
selector plate sticker set (6 pcs)
M2 screw and washer set:
1 x screw
1 x pressboard insulation washer
2 x steel washers
M2.5 screw and washer set:
1 x screw
1 x pressboard insulation washer
2 x steel washers
connector set:
1 x Deans-T connector with heatshrink tubes
2 x motor connectors (2.8 x 0.5 mm – 0.11 x 0.02 in) with heatshrink tubes
Procedure
You will need:
a cross-head screwdriver
a flat-blade screwdriver
a metal file or milling machine
solvent
grease
a Blu-Link or USB-Link with a micro USB-Cable and a Windows/Mac/Android/iOS device
Follow the steps below in order to mount the TITAN drop-in module:
1. Remove the gearbox from the AEG body
2. Disassemble your gearbox, take out all the internals
3. Clean the gearbox case using solvent
4. Pay attention to the marked area. If you see that it is not smooth, use a metal file or grindstone to prepare the surface. The gearbox surface should be smooth, with no sharp edges which may damage the TITAN.
5. Detach the drop-in module carefully.
6. Place the bottom board in the bottom part of the gearbox. Do not use a screw yet. Check if the bottom board is laid flat in the gearbox.
7. Make sure the electronic components are not touching the gearbox case.
8. Use the (black) insulation washer from the kit.
Caution
The insulation washer must protect the circuit board. The metal screw and the metal washer cannot touch the board directly as this can result in a short circuit and TITAN damage, which is not covered by warranty.
9. Fasten the bottom board to the case. Use the original screw or the one(s) from the kit.
10. Check if the screw is sticking out of the gearbox.
11. If so, add the metal washer(s) included in the kit. Make sure that the metal washer is placed between the screw and the insulation washer. It cannot be touching the circuit board directly.
12. Check if the top board fits the gearbox without any problems.
13. Loosen the screw. Adjust the position of the bottom board. The distance between the PCB and the bearing must be the same throughout (as indicated in the marked area).
Note
Sector gear sensor placement is very important.
14. Make sure the marked areas are not covered by the board or wires.
15. Check if the sensors are clean and not covered by wires.
16. Some gearboxes need modification. Check if your gearbox has the marked pins. If so, remove them.
17. Check if both parts of the gearbox fit together perfectly.
18. Mount the trigger without the spring. Insert the TITAN top board. Close the gearbox. When the gearbox is closed, carefully check if the trigger can move smoothly and is not touching any TITAN components.
19. Mount the sector gear, trigger with the spring and the top TITAN board. Make sure that the gear is not touching TITAN.
20. Close the gearbox. Tighten the two screws on the top part of the gearbox case.
21. Prepare the selector plate. If the selector plate does not have a copper connector, you need to modify it. The black surface does not reflect light, so sensors will not work properly.
22. In order to modify the black plate, use a sticker from the kit. Try the sticker with the thinner black line first.
Note
If the selector plate has a copper connector, do not make any modifications.
23. The black plate after modification. Sticker location is crucial. Carefully align it to the left-hand side.
24. Install the selector plate.
25. Connect TITAN to your desktop/mobile device using a USB-Link or a Blu-Link. Start GCS.
26. Check Gear and Tooth Detection: Go to General. Turn the gears slowly to check if the sensor can detect teeth. Keep in mind that TITAN reads the sensors much quicker than GCS.
27. Check trigger sensitivity:
Go to Trigger. Pull the trigger slowly. The sensor indicators will stop glowing one by one in the area marked, you will also see a change in the colour of the indicators marked, which mean active sensors. In case of some trigger models, the first sensor(s) might be active even when the trigger is not pulled.
28. Check selector calibration:
Go to Selector. Check if the sensors recognize the selector plate. Moving the selector plate, verify if TITAN detects SAFE, SEMI and AUTO. You will notice changes in the marked areas . If necessary, go to Recalibrate and follow the instructions in GCS.
Otherwise, you need to modify the selector plate with another sticker as mentioned above in steps 21-23 and shown below:
29. Insert the gearbox into the body
30. If all the sensors are working flawlessy, you can assemble the gearbox. Do not use too much grease. In a critical situation, excessive grease may cover sensors.
Note
The first few shots are calibration shots. TITAN adapts to gearbox configuration. In order to readapt TITAN, you must Restore Factory Settings or change the Gear Ratio. This is necessary if e.g. you replace the motor.
TITAN V3
TITAN V3 has the following optical sensors:
1 sector gear sensor
1 selector sensor
1 proximity trigger sensor
Installation
Please read the installation guide below before proceeding.
INSTALLATION KIT Contents
3 x selector plate stickers
trigger sticker set (6 pcs)
3 x anti-backlash stickers (0.15 mm - 0.006 in)
3 x anti-backlash stickers (0.3 mm - 0.012 in)
3 x anti-backlash stickers (0.5 mm - 0.02 in)
2 x washers (0.3 mm - 0.012 in)
2 x washers (0.2 mm - 0.008 in)
2 x washers (0.1 mm - 0.004 in)
set of connectors:
1 x Deans-T connector with heatshrink tubes
2 x motor connectors (2.8 x 0.5 mm - 0.11 x 0.02 in) with heatshrink tubes
Procedure
You will need:
a cross-head screwdriver
a flat-blade screwdriver
a metal file or milling machine
solvent
grease
Blu-Link or USB-Link with a micro USB-Cable and a mobile/desktop
Follow the steps below in order to mount TITAN:
1. Remove the gearbox from the AEG body.
2. Disassemble your gearbox, take out all the internals.
3. Clean the gearbox case using solvent.
4. Detach the drop-in module carefully.
5. Route the wires through the gearbox shell from the inside.
6. Place the wires in the gearbox shell so as the unit can fit properly without any resistance.
7. Place the bottom board on the bottom part of the gearbox. Do not use any screw yet. Check if the bottom board is laid flat in the gearbox.
8. Make sure the electronic components are not touching the gearbox case.
9. If the bottom board fits correctly, use a cut-off lever screw to stabilize the unit. Also use the included washers.
Note
TITAN V3 does not require an insulation washer.
10. Check if the screw is sticking out of the gearbox.
11. If so, add the metal washer(s) included in the kit.
12. Check if the top board fits the gearbox without any problems.
13. Loosen the screw. Adjust the position of the bottom board. The distance between the board and the bearing should be similar as indicated in the marked area.
Note
Sector gear sensor placement is very important.
14. Mount the sector gear and top TITAN board. Make sure that the gear is not touching TITAN.
15. Close the gearbox. Use at least two screws.
16. Connect TITAN to your mobile/desktop device with a USB-Link or Blu-Link. Run GCS. Go to General.
17. Turn the gear slowly to check if the sensor detects teeth (2). Keep in mind that TITAN reads the sensors much quicker than the GCS.
18. Use solvent to clean trigger elements. Next, place the smaller sticker (trigger sticker) on the flat surface.
19. Place one trigger anti-backlash sticker inside the moving element of the trigger.
Note
The stickers reduce space between the trigger and the moving element, so as the trigger works more precisely. The INSTALLATION KIT includes three stickers of different thicknesses.
20. After placing the first sticker, assemble both trigger elements and estimate the clearance between them. If you feel that there is still some clearance, you can use more stickers. Remember that the trigger should work smoothly.
21. All the steps performed inside the gearbox are complete. Now you can assemble the gearbox. Do not use too much grease. In a critical situation, excessive grease may cover a sensor.
22. In some replicas (G36, UMP, etc.) you need to modify the mechanical trigger lock, because it is too long and touches the TITAN top board. In this case, grind the protruding element by around 1.5/2 mm [0.06/0.08 in].
23. After modification, check if the mechanical trigger lock is touching the TITAN top board. If it is not, you can proceed.
24. Install the remaining external gearbox components and start wire placement. You can use the picture below or your previous wiring as a suggestion.
25. Prepare the selector plate following the steps below. If the plate is a standard one (AK, most of G36, etc.), paste the sticker as in the picture below. If necessary, enlarge the hole in the plate – the space between the selector plate border and the sticker border should be approximately 10mm [0.4 in].
26. If there are any issues with sticker adhesion, modify the selector plate.
27. Finish gearbox assembly and put it in the replica body. Next, connect TITAN to a mobile/desktop device using a USB-Link or Blu-Link and perform sensor calibration following the instructions in GCS. Follow the steps below.
Caution
Calibrate the trigger and selector sensors only after the gearbox is mounted in the replica body.
TITAN V2 NGRS
TITAN V2 NGRS has the following optical sensors:
2 gear sensors
1 selector sensor
1 trigger sensor
1 bolt catch sensor
Installation
Please read the Installation Guide below before proceeding.
INSTALLATION KIT Contents
selector plate sticker set (6 pcs)
M2 washer set:
2 x insulation pressboard insulation washers
2 x insulation steel washers
connector set:
1 x Deans-T connector with heatshrink tubes
2 x motor connectors (2.8 x 0.5 mm – 0.11 x 0.02 in) with heatshrink tubes
Procedure
You will need:
a cross-head screwdriver
a Torx screwdriver
a flat-blade screwdriver
ametal file or milling machine
solvent
grease
a USB-Link with a micro USB-Cable or a Blu-Link and a Windows/Mac/Android/iOS device
Follow the steps below in order to mount the TITAN drop-in module:
1. Remove the gearbox from the AEG body.
2. Disassemble your gearbox, take out all the internals.
3. Clean the gearbox case using solvent.
4. Detach the drop-in module carefully.
5. Place the bottom board in the bottom part of the gearbox. Do not use any screw yet. Check if the bottom board is laid flat in the gearbox.
6. Make sure the electronic components are not touching the gearbox case.
7. Use the insulation (black) washer from the INSTALLATION KIT.
Caution
The insulation washer must protect the circuit board. The metal screw and metal washer cannot touch the board directly as this can result in short circuit and TITAN damage, which is not covered by warranty.
8. Screw on the bottom board to the case. Use the original screw or the one from the kit.
9. Check if the screw is sticking out of the gearbox.
10. If so, add metal washer(s) included in the kit. Make sure that the metal washer is placed between the screw and the insulation washer. It cannot touch the circuit board directly.
11. Check if the top board fits gearbox without any problems.
12. Make sure the marked areas are not covered by the board or wires. Check if the sensors are clean.
13. Place the wires in the gearbox shell, in exactly the same way as in the picture. The order is important.
14. Check if both parts of the gearbox fit together perfectly.
15. Mount the sector gear and top TITAN board. Make sure that the gear is not touching TITAN.
16. Close the gearbox. Tighten at least three screws.
17. Connect the unit to GCS using a USB cable and a USB-Link or Blu-Link (do not solder the Deans-T connector yet).
18. Go to General. While moving the gear, observe what happens with the gear sensors and Full Section Gear and Half Section Gear icons.
19. Test the bolt catch sensor by moving the lever up and down. Observe what happens with the BOLT CATCH SENSOR icons. Depending on the position of the lever, the icons will flash alternately.
20. If both sensors are working flawlessly, you can assemble the gearbox. Do not use too much grease. In a critical situation, excessive grease may cover a sensor.
21. Modify the selector plate. Use solvent to clean the selector plate. Next, take the stickers shown in the picture below. Take the small sticker (selector sticker) and stick it on the flat surface shown below.
22. The wires in the pistol grip have to be placed according to the photo below.
23. The wires in the buffer tube have to be placed according to the photos below.
Warning
Pay attention to correctly solder positive and negative TITAN wires to the connector. Otherwise, after plugging in the battery, reverse battery polarity will cause immediate damage to the device, which is not covered by the warranty and can lead to fire, burn or even battery explosion.
24. Place the heat-shrink tube on the wire, cover the connector with a thin layer of solder. (Always use flux or rosin during soldering, especially when solder melts. This is necessary to achieve the correct connection.)
25. Have a look at the connection and check if it is done properly. Pay attention while soldering – it should fill the soldered space correctly and the solder cannot be oxidized. Remove excess rosin from the connection.
26. Repeat the procedure with the black (negative) wire.
27. Prepare the heat-shrink tubes and close them. Heat each heat-shrink tube carefully from all sides. Do it over the flame of a gas range or lighter.
28. If your gun is completely assembled, perform sensor calibration. Go to Trigger in GCS and calibrate it.
29. Then go to Selector and calibrate it.
After successful calibration your AEG is ready to use.
Legal Notice
Please read the Legal Notice before operating your device and keep it for future reference. This document contains important terms and conditions with respect to your device. By using this device, you accept these terms and conditions.
Exclusion of Liability
GATE Enterprise sp. z o.o. sp. k. are not liable for any damages, injuries or accidents of any kind resulting from the use of this product or airsoft gun with the product installed, including (but not limited to) incidental or special damages to airsoft gun, airsoft gun parts, batteries and gearbox internals.
Disclaimer
GATE Enterprise sp. z o.o. sp. k. takes no responsibility regarding compliance of the product with the requirements of any law, rule or airsoft restrictions pertaining thereto.
Intellectual Property
Intellectual Property owned by GATE Enterprise sp. z o.o. sp. k., including but not limited to, devices, accessories, parts, software, documentation, is proprietary to GATE Enterprise sp. z o.o. sp. k. and protected under Polish laws, EU laws, and international treaty provisions. You may not violate the rights of the Intellectual Property and you will not prepare derivative works of or reverse engineer the device or software. No ownership in the Intellectual Property is transferred to you.
GATE Limited Warranty Policy
GATE Enterprise sp. z o.o. sp. k. warrant that its Product is free from manufacturing and material defects at the date of purchase and for a period of two (2) years from the date of purchase and it is nonextendable. This Limited Warranty is conditioned upon proper use of Product by Purchaser.
This Limited Warranty is valid provided that the owner provides a proof of purchase and properly completed warranty form.
This Limited Warranty does not cover: (a) defects or damage (e.g. mechanical, thermal or chemical) resulting from accident, misuse (misinterpretation of the instructions), abuse, neglect, unusual physical, electrical or electromechanical stress, water immersion, repairs or structural modification of any part of Product, or (b) the Product that has its serial number removed or made illegible; (c) defects or damage from improper operation, maintenance or installation, (d) installation of the products.
Requests for warranty are processed as soon as possible, not exceeding seven (7) working days. The company’s obligation under this Limited Warranty shall be limited to providing replacement of parts only.
Product Disposal Instructions
The symbol shown here means that the product is classified as Electrical or Electronic Equipment and should not be disposed with other household and commercial waste at the end of its working life. The Waste of Electrical and Electronic Equipment (WEEE Directive 2012/19/EU) has been put in place to recycle products using best available recovery and recycling techniques to minimize the impact on the environment. Purchasers shall take any old electrical equipment to waste recycling public centres or points of sale.
Certificate of Conformity
GATE Enterprise sp. z o.o. sp. k. hereby declare under our sole responsibility that the products GATE TITAN V2, TITAN V3 and TITAN V2 NGRS are in conformity with the essential requirements of the following Directives: 2011/65/EU, 2014/30/EU, 2014/35/EU, 2001/95/WE.
Technical Specifications
The design and production of the device is based on harmonized standards.
Stay tuned with GATE
Join the GATE Airsoft Community Discord Server!
Facebook
YouTube
Instagram
Manufactured by GATE Enterprise sp. z o.o. sp. k.
Torowa 3H
PL-30435 KRAKÓW
email: support@gatee.eu
tel: +48 12 210 05 23
© 2024 GATE Enterprise sp. z o.o. sp. k.
Add Comment