Skip to end of metadata
Go to start of metadata

You are viewing an old version of this page. View the current version.

Compare with Current View Version History

Version 1 Next »

Gratulacje!

Blu-Link umożliwia sterowanie ETU (Electronic Trigger Units) od GATE oraz bezprzewodowe łączenie go z innymi kompatybilnymi urządzeniami za pośrednictwem aplikacji GCS. Co więcej, Blu-Link to dodatkowy regulowany inteligentny bezpiecznik i wielofunkcyjny watomierz umożliwiający np. odczyt danych telemetrycznych.

Razem z GCS możesz dostosować ustawienia TITAN lub ASTER i zaktualizować lub podwyższyć wersję oprogramowanie na urządzeniach z systemem Android, iOS, a wkrótce także z systemem Windows oraz macOS.

Informacje dotyczące Bezpieczeństwa

Dla własnego bezpieczeństwa przeczytaj uważnie poniższe informacje przed zainstalowaniem urządzenia.

Ostrzeżenie
Sytuacje, które mogą spowodować obrażenia ciała użytkownika lub innych osób.

Uwaga
Sytuacje, które mogą spowodować uszkodzenie urządzenia lub innego sprzętu.

Informacja
Wskazówki

Przestroga

Uwaga Uwagi, wskazówki dotyczące użytkowania lub dodatkowe informacje.

Ostrzeżenie Przed rozpoczęciem procesu instalacji upewnij się, że w Twojej replice AEG nie ma żadnych kulek.

Ostrzeżenie Nie należy przechowywać ani przenosić łatwopalnych cieczy, gazów lub materiałów wybuchowych w tym samym pomieszczeniu, w którym znajduje się urządzenie, jego części lub akcesoria.

Ostrzeżenie Nieprawidłowe podłączenie dodatnich i ujemnych biegunów akumulatora może spowodować natychmiastowe uszkodzenie urządzenia, które nie jest objęte gwarancją i może doprowadzić do pożaru.

Przestroga Chroń urządzenie przed kontaktem z materiałami przewodzącymi, takimi jak kurz, ciecz lub proszek metalowy.

Uwaga Podłączenie akumulatora o napięciu powyżej 17 V spowoduje trwałe uszkodzenie urządzenia, które nie jest objęte gwarancją.

Przestroga Nie zdejmować ochronnej rurki termokurczliwej urządzenia.

Uwaga Formularz gwarancyjny produktu jest dostępny na naszej stronie internetowej: www.gatee.eu/warranty

Uwaga W przypadku problemów z instalacją lub używaniem tego produktu: a) napisz do nas na adres support@gatee.eub) skontaktuj się z nami przez Facebook: https://www.facebook.com/gateec) zadzwoń (+48) 122-100 -523

Notice
Notes, usage tips or additional information.

 

 

Warning  
Before starting the installation process, make sure your AEG is empty and there are no BBs inside. 

Warning  
Do not store or carry flammable liquids, gases or explosives in the same compartment as the device, its parts or accessories.  

Warning  
Incorrectly connecting positive and negative battery terminals may cause immediate damage to the device, which is not covered by the warranty, and can lead to fire. 

Caution
Prevent the device from contact with conductive materials, such as dust, liquid or metal powder.

Caution
Connecting battery with voltage over 17 V will cause permanent damage to the device, which is not covered by the warranty.

Caution
Do not remove the device protective heat-shrink tube.

Notice
The product Warranty Form is available on our website: www.gatee.eu/warranty

Notice
In case you have any difficulties while installing or using this product:
a) email us at support@gatee.eu
b) contact us via Facebook: https://www.facebook.com/gatee
c) call (+48) 122-100-523

 

How to use Blu-Link

(grafika z pudełka)

Notice
You can use Blu-Link without ETU. It will work as a smart fuse and multifunctional wattmeter enabling to, e.g., read telemetry data.

First connection via GCS

  1. Download and install GATE Control Station:
    www.gatee.eu/gcs

  2. Enable Bluetooth function on your device

  3. Prepare Blu-Link troubleshooting card included in the kit

  4. Plug Blu-Link into AEG battery, LED side up. LED should glow green for 1 s.

  5. Read the LED status and relate to troubleshooting card

  6. Log into the GCS app

  7. Prepare PIN printed on the Blu-Link PIN card

  8. Connect Blu-Link by following the instructions from the GCS

  9. Plug Blu-Link into AEG/ETU

  10. Enjoy using of the Blu-Link

 

 

Plug and play

  1. Plug Blu-Link into AEG battery

  2. Plug Blu-Link into AEG/ETU

  3. Enjoy the airsofting

 

Notice
Keep the Blu-Link PIN card or save PIN printed on it – you will need it for each new connection. If you lose your PIN, contact us at support@gatee.eu.

 

Notice
Blu-link is compatible with the Bluetooth version 4.0 or later.

 

Troubleshooting

[rysunek pokazujący lokalizację LED Blu-Linka]

 

 

Troubleshooting Card [BLU-L]

After connecting the battery, check the Blu-Link RGB LED:

LED

WHAT HAPPENED

WHAT TO DO

GREEN 1 s on start

Self-test was completed with no errors

Blu-Link is ok. Wait for further LED indications

GLOWING GREEN

Blu-Link is connected

 

BLUE BLINKING for 120 s

Blu-Link is ready for the Bluetooth connection

Enjoy the airsofting or connect Blu-link to the GCS

GLOWING RED

Self-test and Bluetooth connection have failed

a) Contact us at support@gatee.eu

b) If you have USB-Link, connect to the GCS and perform diagnostics

BLINKING IN RED / BLUE

a) Blu-Link does not have a firmware installed

b) Blu-Link internal error

a) Install the Blu-Link firmware via GCS

b) Connect Blu-Link to the GCS and perform diagnostics

BLUE GLOWING for 120 s

Blu-Link is connected correctly

Enjoy using of Blu-Link

GLOWING ORANGE

Blu-Link is transmitting firmware data

Wait until the data has been transmitted.
Keep the device with GCS close to Blu-Link

LED is OFF after 120 s

a) Battery saving mode

b) Battery is disconnected

a) Enjoy the airsofting

b) Connect battery

LED is OFF after the battery is connected

a) The battery is discharged or damaged

b) Battery deans-t connector is not compatible

a) Charge or replace the battery

b) Replace the battery deans-t connector for the one from the kit

BLINKING RED

Overload, DTC being displayed: 2 - ULL, 3 - OCP, 4 - SCP, 5 - OTP

Read what to do in the Quickstart or GCS app

BLINKING YELLOW

Too low voltage, DTC being displayed: 1 - UVP1, 2 - UVP2, 3 - UVP3

Read what to do in the Quickstart or GCS app

 

 

DTC Codes

Diagnostic Trouble Codes (DTC) inform about basic malfunctions and problems with your battery, AEG, ETU or Blu-Link. You are notified of them by LED blinking for 2 minutes after the problem occurs. The Blu-Link DTC can be later read and cleared in DTC menu in GCS app.

In the event of trouble

  1. The color of LED reflects on the problem type:

    1. Yellow indicates a warning

    2. Red indicates a problem

  2. Number of blinks determines what exactly the problem is (for reference, read DTC explanations presented later on in this guide)

DTC explanations

  • grafika - flaga w kolorze i z liczba plus strzałki wyjaśniające

  • dodać za liczbą mignięć znak “x” np. 2x

  • przemyśleć bardziej obrazowe oznaczanie liczby mignięć, np. warfet, 4 błyśnięcia:

 

Notice
If you use an ETU connected to Blu-Link, check also the ETU DTC. Blu-Link is designed to withstand higher power load and lower voltage than ETU, so in most cases, the ETU protection turns on earlier and the Blu-Link does not detect the problem.

LED

WHAT HAPPENED

POSSIBLE REASON

WHAT TO DO

LED

WHAT HAPPENED

POSSIBLE REASON

WHAT TO DO

ULL – User load limit was exceeded.

  1. The load limit is set too low, according to the AEG configuration.

  2. Other possible reasons the same as in OCP or SCP.

  1. Modify adjustable smart fuse settings.

  2. Follow the OCP or SCP guidelines.

  3. Contact us at support@gatee.eu

OCP – Blu-Link has detected a too high current. The overcurrent protection was activated.

  1. Motor is damaged.

  2. Motor or gearbox is jammed.

  3. Motor connections short circuit.

  1. Replace the motor.

  2. Unjam the motor or gearbox.

  3. Check and fix the motor wires insulation.

SCP – Blu-Link has detected a current over 270A. The short circuit protection was activated.

  1. Motor is damaged.

  2. Motor or gearbox is jammed.

  3. Motor connections short circuit.

  1. Replace the motor.

  2. Unjam the motor or gearbox.

  3. Check and fix the motor wires insulation.

OTP – Blu-Link temperature is too high. Over temperature protection was activated.

  1. Outside temperature is too high in correlation with the demanding AEG.

  2. Frequent short circuits and Blu-Link electrical overloads.

  1. Wait until the temperature drops.

UVP1 – Battery protection was activated.

The battery is discharged.

Charge the battery.

UVP2 – The voltage dropped below level critical for Blu-Link to work properly.

  1. The battery is discharged.

  2. The battery is worn out and has too high internal resistance.

  3. Inadequate battery type for given AEG configuration.

  4. Too much electrical resistance between Blu-Link and the battery.

  5. Motor is too powerful for the battery connected.

  6. Motor connections short circuit.

  7. Motor is jammed.

  8. Motor is damaged.

  1. Charge the battery.

  2. Replace the battery.

  3. Use a battery of a greater capacity or voltage.

  4. Do not use any adapters.

  5. Use standard or high-torque motors instead of high-speed ones.

  6. Check and fix the motor wires insulation.

  7. Unjam the motor.

  8. Replace the motor.

 

UVP3 – Protection against over-discharge of the battery. Battery protection activated immediately after the battery was connected.

  1. Number of cells differs from the number set in the GCS.

  2. The battery is discharged.

  1. Set the same number of cells in GCS as in the battery.

  2. Charge the battery up.

 

Notice
There may be several codes displayed one after another, e.g., SCP and UVP2: 4 red blinks, 2 yellow blinks.

 

Notice
It is a good practice to clear the DTC in GCS before each skirmish.

 

 

Compatible with:

TITAN V2
TITAN V3
TITAN V2 NGRS
ASTER V2
ASTER V3
STATUS

and future GATE products

 

Bluetooth Trademark Attribution (może być małą czcionką, jak przypis)

The Bluetooth® by both, the word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by GATE Enterprise sp. z o.o. sp. k. is subject to licensing. Other trademarks and trade names are those of their respective owners.

Product compliance

CERTIFICATE OF CONFORMITY
GATE Enterprise sp. z o.o. sp. k. hereby declares under our sole responsibility that GATE Blu-Link is in conformity with the essential requirements of the following Directives: EC DIRECTIVE 2011/65/EU. The product is certified as RoHS Compliant.

(RoHS compliance marking)

Product compliance regarding the use of ANNA-B112 module

This device complies with Part 15 of the FCC [Federal Communications Commission] Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference; and (2) this device must accept any interference received, including interference that may cause undesired operation.

This device complies with Industry Canada’s license-exempt RSSs. Operation is subject to the following two conditions: (1) this device may not cause interference; and (2) this device must accept any interference, including interference that may cause undesired operation of the device.

 

 

 

 

 

This equipment operates on a secondary basis and, consequently, must accept harmful interference, including from stations of the same kind, and may not cause harmful interference to systems operating on a primary basis.

 

 

Legal Notice

Please read this Legal Notice before operating your device and keep it for future reference.
This document contains important terms and conditions with respect to your device. By using of this device, you accept those terms and conditions.

EXCLUSION OF LIABILITY GATE Enterprise sp. z o.o. sp. k. is not liable for any damages, injuries or accidents of any kind resulting from the use of this product or airsoft gun with the product installed, including (but not limited to) incidental or intentional damages to airsoft gun, airsoft gun parts, batteries and gearbox internals.

DISCLAIMER GATE Enterprise sp. z o.o. sp. k. takes no responsibility regarding compliance of the product with the requirements of any law, rule or airsoft restrictions pertaining thereto.

INTELLECTUAL PROPERTY Intellectual Property owned by GATE Enterprise sp. z o.o. sp. k., including (but not limited to) devices, accessories, parts, software, documentation, is proprietary to GATE Enterprise sp. z o.o. sp. k. and protected under Polish laws, EU laws and international treaty provisions. You may not violate the rights of the Intellectual Property and you will not prepare derivative works of or reverse engineer the device or software. No ownership in the Intellectual Property is transferred to you.

GATE LIMITED WARRANTY POLICY GATE Enterprise sp. z o.o. sp. k. warrants that its product is free from manufacturing and material defects at the date of purchase and for a nonextendable period of two (2) years from the date of purchase. This Limited Warranty is conditioned upon proper use of the product by Purchaser.

  1. This Limited Warranty is valid provided that the owner provides a proof of purchase and a properly completed warranty form.

  2. This Limited Warranty does not cover: (a) defects or damage (e.g., mechanical, thermal or chemical) resulting from accident, misuse (misinterpretation of the instructions), abuse, neglect, unusual physical, electrical or electromechanical stress, water immersion, repairs or structural modification of any part of the product, or (b) the product that has its serial number removed or made illegible; (c) defects or damage from improper operation, maintenance or installation; (d) installation of the products.

  3. Requests for warranty are processed as soon as possible, not exceeding seven (7) working days. The company’s obligation under this Limited Warranty shall be limited to providing replacement of part(s) only.

PRODUCT DISPOSAL INSTRUCTIONS The symbol shown here means that the product is classified as Electrical or Electronic Equipment and should not be disposed with other household and commercial waste at the end of its working life. The Waste of Electrical and Electronic Equipment (WEEE Directive 2012/19/EU) has been put in place to recycle products using best available recovery and recycling techniques to minimize the impact on the environment. Purchasers shall take any old electrical equipment to waste recycling public centers or points of sale.

 

Stay tuned with GATE

facebook.com/Gatee
youtube.com/GateMovies
http://twitter.com/GateEnterprise
instagram.com/GateEnterprise

Manufactured by

GATE Enterprise sp. z o.o. sp. k.
Torowa 3H
PL-30435 KRAKÓW
Email: office@gatee.eu
Tel: (+48) 122-100-523
www.gatee.eu

 

  • No labels