Versions Compared

Version Old Version 11 New Version Current
Changes made by

Sebastian Florek-Paszkowski

Sebastian Florek-Paszkowski

Saved on

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.

...

  1. After unboxing and before installation, connect TITAN to the GCS App via Blu-Link or USB-Link. You can download GCS here: https://www.gatee.eu/gcs


    The GCS Information for Use is here: https://www.gatee.eu/manuals

    Image Removed

    Information for Use (In4U) [GCS]

    Image Added

  2. Check for latest firmware updates.

Info

Note
Your Android (version 5.0 or higher) device must support OTG technology to run the GATE Control Station App.

Infotip

Note 
You need a USB-Link or a Blu-Link to connect your TITAN to the GATE Control Station GCS for Android and Windows/macOS. To connect to the iOS GCS, you must use a Blu-Link.

Tip

Note
If you are using USB-Link, your Android (version 5.0 or higher) device must support OTG technology to run GCS.

Tip

Note
If you are using Blu-Link, Bluetooth 4.0 or higher is required.

3. Now you’re ready to install TITAN in the gearbox.

Installation

Note

Caution
Regardless of your previous experience, follow all safety precautions to prevent any damage to your TITAN.

Note

Caution
TITAN installation requires deep technical knowledge of gearbox internals. To avoid damage, we recommend it to be installed by a skilled person. If, however, you wish to proceed with TITAN installation on your own, you must watch the installation video and read

...

this full-length

...

document: Information for Use (In4U) [TTN] beforehand. Incorrect installation may result in, among others, sensor damage, which is not covered by warranty.

...

Infotip

Note  
TITAN V2 and TITAN V3 do not support Infinite torque-up gears.

...

Infotip

Note
Apply a thin layer of grease. Excessive grease may cover sensors or gaps between teeth, which will result in cycle detection issues. Use grease of appropriate viscosity and density to avoid splashing.

...

Infotip

Note  
In the GCS App configure the gear type (if your gears are not stock) and perform first-time sensor calibration for TITAN V3 and TITAN V2 NGRS.

Tip

Note  
In case of any difficulties installing or using this product:

...

...

  • call us on

...

  • +48

...

  • 122 100 523

TITAN V2

...

Note

Caution
A sector gear can damage the gear sensor during installation. Avoid this damage.

...

Note

Caution
An insulation washer is required. Place the washer(s) according to the graphic below. Placing washers in the wrong order will cause a short circuit and permanent damage to TITAN, which is not covered by warranty.

...

Note

Caution
Incorrect placement of wiring under the motor gear may cause insulation damage and a short circuit, which is not covered by warranty.

...

Note

Caution
ICS gearboxes require modification to avoid TITAN damage.

...

...

Note

Caution
Do not pull the

...

Trigger when the gearbox is open. This may result in

...

Trigger sensor damage.

...

Infotip

Note
In the case of some triggers cases (e.g. speed or CNC triggersTriggers), the first trigger Trigger sensor(s) may be covered even when the trigger Trigger is not pulled, which is due to its design.

Infotip

Note
The Fire Selector sensor does not detect black surface. If the Fire Selector does not come with a metal connector or it does not work properly, you must use an appropriate sticker from the kit.

...

Infotip

Note
Sticker position is crucial. Make sure to align it exactly to the left edge and the top red line. The set contains 3 different sticker types. First, use the one with the thinner black line. If you are not able to calibrate the selectorSelector, try the other ones.

...

...

Note

Caution
In TITAN V2 connectors must be bent according to the photo below. Bending connectors in the opposite direction may cause them to break. If this should happen, spare terminals are included in the

...

INSTALLATION KIT.

...

Image Added

TITAN V3

...

Infotip

Note
TITAN V3 fits CNC gearboxes with very low backlash. While fitting TITAN, pull the cables and at the same time push the board into the right place. Pay attention to the area marked yellow to fit the board correctly.

...

Note

Caution
Use a metal washer with a max. 8 mm [0.31 in] diameter to avoid TITAN damage.

...

Infotip

Note
Use the trigger Trigger sticker to make it visible for the trigger Trigger sensor.

...

Infotip

Note
TITAN can detect trigger Trigger position very precisely. In order to use it, you need to eliminate trigger Trigger backlash. The set contains 3 trigger Trigger anti-backlash stickers of various thicknesses. Try each one of them and choose the most appropriate one.

...

Infotip

Note
The selector Selector plate requires modification. Place the selector Selector sticker according to the photos below. Its position is crucial.

...

Infotip

Caution

In TITAN V3 the connectors must be straight according to the photo below. Bending and straightening the connectors back may cause them to break. If this happensshould happen, spare terminals are included in the installation kitINSTALLATION KIT.

...

TITAN V2 NGRS

...

...

Warning

Warning
If you are using a recoil system and set excessive

...

Trigger sensitivity, it may cause

...

accidental discharge (firing) even without pressing the

...

Trigger.

Image Modified

...

Warning

Warning
Pay attention to correctly solder positive and negative TITAN wires to the connector. Incorrectly connecting positive and negative battery terminals will cause immediate damage to the device, which is not covered by warranty, and can lead to fire.  

Note

Caution
An insulation washer is required. Place the washer(s) according to the graphic below. Placing washers in the wrong order will cause a short circuit and permanent damage to TITAN, which is not covered by warranty.

Image Modified

...

Image AddedImage Added

Note

Caution
Do not locate the screw in the cut-off lever hole to secure the TITAN board. Use a contact block mounting screw in the hole indicated by the arrow.

Image Modified
Note

Caution
Incorrect placement of wiring under the motor gear may cause insulation damage and a short circuit, which is not covered by warranty.

Image Modified
Note

Caution
In order to secure the wires properly, modify the gearbox as shown in the photos below.

Image Modified

...

Tip

Note
The

...

Selector plate requires modification. Place the

...

Selector sticker according to the photos below. Its position is crucial.

Image Modified
Note

Caution
In TITAN NGRS connectors should be bent according to the photo below. Bending connectors in the opposite direction may cause them to break. If this

...

should happen, spare terminals are included in the

...

INSTALLATION KIT.

Image Modified

Quick Access Menu

...

You can access Pre-cocking or Profiles using a shortcut. After firing a shot, burst or while in SAFE (only if the safety lever has been removed)*, hold the trigger Trigger and switch the Fire Selector within the specified time (see table). Switch the Fire Selector in any order to change between the options indicated by motor vibrations. 

By releasing the triggerTrigger, you exit the function confirming it. Bear in mind that programming Programming via trigger Trigger is a different process. To find out more check the PROGRAMMING VIA TRIGGER CARD included or go to https://gatee.eu/technical-support/manuals.

...

*You can enter Programming via Trigger only when the Fire Selector on the replica is in SEMI position and AUTO mode is not assigned to this position.

Function

available if preset in GCS

in SEMI or BURST mode preset in GCS in SEMI physical position only

Pre-cocking

Profiles (EXPERT only)

Programming via triggerTrigger

To enter the function: hold the trigger Trigger 

and switch the Fire Selector within 2 s

and switch the Fire Selector within 2–7 s

for > 7 s 

Available options

Option

Low frequency vibration

Option

High frequency vibration

check the PROGRAMMING VIA TRIGGER CARD included or go to https://gatee.eu/technical-support/manuals

Off

1

Profile 1

1

Auto

2

Profile 2

2

Manual*

3

Profile 3

3

*If defined in GCS

Pre-cocking Selection

In GCS go to Trigger>Pre-cocking>Switch mode via Fire Selector and use the toggle button to activate this function.

  1. Fire a shot, burst or pull the trigger Trigger while in SAFE mode (only if the safety lever has been removed) * and do not release the triggerTrigger.

  2. Switch the Fire Selector within 2 s. There is a single low frequency vibration.

  3. Switch the Fire Selector in any order to change between options, which are indicated by vibrations:

    1. 1 low vibration – Pre-cocking Off

    2. 2 low vibrations – Pre-cocking Auto

    3. 3 low vibrations – Pre-cocking Manual

  4. Release the trigger Trigger to save the selected mode.

...

Profiles are sets of particular settings of configurable TITAN functions. You can choose one of the three profiles at a time. Go to General>Profiles>Change profile change via selector Selector in GCS to be able to use this function. If you want to change the active Profile:

  1. Fire a shot, burst or pull the trigger Trigger while in SAFE (only if the safety lever has been removed) and do not release the triggerTrigger.

  2. Switch the Fire Selector within 2–7 s. There is a single high frequency vibration.

  3. Switch the Fire Selector in any order to change between options, which are indicated by vibrations. 

    1. 1 high vibration – Profile 1

    2. 2 high vibrations – Profile 2

    3. 3 high vibrations – Profile 3

  4. Release the trigger Trigger to save the selected profile.

Continue:
Information for Use (In4U) [TTN]

Go back to:
/wiki/spaces/RD/pages/428867636
Safety & Regulatory Information [TTN]