...
After unboxing and before installation, connect TITAN to the GCS App via Blu-Link or USB-Link. You can download GCS here: https://www.gatee.eu/gcs
The GCS Information for Use is here: Information for Use (In4U) [GCS]
Check for latest firmware updates.
...
| Note |
|---|
Caution
TITAN installation requires deep technical knowledge of gearbox internals. To avoid damage, we recommend it to be installed by a skilled person. If, however, you wish to proceed with TITAN installation on your own, you must watch the installation video and read this full-length document: Information for Use (In4U) [TTN] beforehand. Incorrect installation may result in, among others, sensor damage, which is not covered by warranty. |
...
| Note |
|---|
Caution
An insulation washer is required. Place the washer(s) according to the graphic below. Placing washers in the wrong order will cause a short circuit and permanent damage to TITAN, which is not covered by warranty. |
...
| Tip |
|---|
Note
Sticker position is crucial. Make sure to align it exactly to the left edge and the top red line. The set contains 3 different sticker types. First, use the one with the thinner black line. If you are not able to calibrate the Selector, try the other ones. |
...
| Tip |
|---|
Note
TITAN V3 fits CNC gearboxes with very low backlash. While fitting TITAN, pull the cables and at the same time push the board into the right place. Pay attention to the area marked yellow to fit the board correctly. |
...
| Note |
|---|
Caution
Use a metal washer with a max. 8 mm [0.31 in] diameter to avoid TITAN damage. |
...
| Warning |
|---|
Warning
If you are using a recoil system and set excessive Trigger sensitivity, it may cause accidental discharge (firing) even without pressing the Trigger. |
| Warning |
|---|
Warning
Pay attention to correctly solder positive and negative TITAN wires to the connector. Incorrectly connecting positive and negative battery terminals will cause immediate damage to the device, which is not covered by warranty, and can lead to fire. |
| Note |
|---|
Caution
An insulation washer is required. Place the washer(s) according to the graphic below. Placing washers in the wrong order will cause a short circuit and permanent damage to TITAN, which is not covered by warranty. |
Image Modified
Image Added
Image Added
Image Removed
Image Removed| Note |
|---|
Caution
Do not locate the screw in the cut-off lever hole to secure the TITAN board. Use a contact block mounting screw in the hole indicated by the arrow. |
| Note |
|---|
Caution
Incorrect placement of wiring under the motor gear may cause insulation damage and a short circuit, which is not covered by warranty. |
| Note |
|---|
Caution
In order to secure the wires properly, modify the gearbox as shown in the photos below. |
| Tip |
|---|
Note
The Selector plate requires modification. Place the Selector sticker according to the photos below. Its position is crucial. |
| Note |
|---|
Caution
In TITAN NGRS connectors should be bent according to the photo below. Bending connectors in the opposite direction may cause them to break. If this should happen, spare terminals are included in the INSTALLATION KIT. |
...
You can access Pre-cocking or Profiles using a shortcut. After firing a shot, burst or while in SAFE (only if the safety lever has been removed)*, hold the Trigger and switch the Selector within the specified time (see table). Switch the Selector in any order to change between the options indicated by motor vibrations.
By releasing the Trigger, you exit the function confirming it. Bear in mind that programming Programming via Trigger is a different process. To find out more check the PROGRAMMING VIA TRIGGER CARD included or go to https://gatee.eu/technical-support/manuals.
...
| Function |
available if preset in GCS | in SEMI or BURST mode preset in GCS in SEMI physical position only |
Pre-cocking | Profiles (EXPERT only) | Programming via Trigger |
To enter the function: hold the Trigger | and switch the Selector within 2 s | and switch the Selector within 2–7 s | for > 7 s |
Available options | Option | Low frequency vibration | Option | High frequency vibration | check the PROGRAMMING VIA TRIGGER CARD included or go to https://gatee.eu/technical-support/manuals |
Off | 1 | Profile 1 | 1 |
Auto | 2 | Profile 2 | 2 |
Manual* | 3 | Profile 3 | 3 |
...
Fire a shot, burst or pull the Trigger while in SAFE (only if the safety lever has been removed) and do not release the Trigger.
Switch the Selector within 2–7 s. There is a single high frequency vibration.
Switch the Selector in any order to change between options, which are indicated by vibrations.
1 high vibration – Profile 1
2 high vibrations – Profile 2
3 high vibrations – Profile 3
Release the Trigger to save the selected profile.
Continue:
Information for Use (In4U) [TTN]
Go back to:
QuickStart Guide (QSG) [TTN]/wiki/spaces/RD/pages/428867636
Safety & Regulatory Information [TTN]
...