Initial Use
After unboxing and before installation, connect TITAN to the GCS App via Blu-Link or USB-Link. You can download GCS here: https://www.gatee.eu/gcs
The GCS Information for Use is here: Information for Use (In4U) [GCS]
Check for latest firmware updates.
Note
You need a USB-Link or a Blu-Link to connect your TITAN to GCS for Android and Windows/macOS. To connect to the iOS GCS, you must use a Blu-Link.
Note
If you are using USB-Link, your Android (version 5.0 or higher) device must support OTG technology to run GCS.
Note
If you are using Blu-Link, Bluetooth 4.0 or higher is required.
3. Now you’re ready to install TITAN in the gearbox.
Installation
Caution
Regardless of your previous experience, follow all safety precautions to prevent any damage to your TITAN.
Caution
TITAN installation requires deep technical knowledge of gearbox internals. To avoid damage, we recommend it to be installed by a skilled person. If, however, you wish to proceed with TITAN installation on your own, you must watch the installation video and read this full-length document: Information for Use (In4U) [TTN] beforehand. Incorrect installation may result in, among others, sensor damage, which is not covered by warranty.
Note
TITAN V2 and TITAN V3 do not support Infinite torque-up gears.
Note
Apply a thin layer of grease. Excessive grease may cover sensors or gaps between teeth, which will result in cycle detection issues. Use grease of appropriate viscosity and density to avoid splashing.
Note
In the GCS configure the gear type (if your gears are not stock) and perform first-time sensor calibration for TITAN V3 and TITAN V2 NGRS.
Note
In case of any difficulties installing or using this product:
email us at support@gatee.eu
contact us via Facebook: https://www.facebook.com/gatee
call us on +48 122 100 523
TITAN V2
Caution
A sector gear can damage the gear sensor during installation. Avoid this damage.
Caution
An insulation washer is required. Placing washers in the wrong order will cause a short circuit and permanent damage to TITAN, which is not covered by warranty.
Caution
Incorrect placement of wiring under the motor gear may cause insulation damage and a short circuit, which is not covered by warranty.
Caution
ICS gearboxes require modification to avoid TITAN damage.
Caution
Do not pull the Trigger when the gearbox is open. This may result in Trigger sensor damage.
Note
In some cases (e.g. speed or CNC Triggers), the first Trigger sensor(s) may be covered even when the Trigger is not pulled, which is due to its design.
Note
The Selector sensor does not detect black surface. If the Selector does not come with a metal connector or it does not work properly, you must use an appropriate sticker from the kit.
Note
Sticker position is crucial. Make sure to align it exactly to the left edge and the top red line.
The set contains 3 different sticker types. First, use the one with the thinner black line. If you are not able to calibrate the Selector, try the other ones.
Caution
In TITAN V2 connectors must be bent according to the photo below. Bending connectors in the opposite direction may cause them to break. If this should happen, spare terminals are included in the INSTALLATION KIT.
TITAN V3
Note
TITAN V3 fits CNC gearboxes with very low backlash. While fitting TITAN, pull the cables and at the same time push the board into the right place. Pay attention to the area marked yellow to fit the board correctly.
Caution
Use a metal washer with a max. 8 mm [0.31 in] diameter to avoid TITAN damage.
Note
Use the Trigger sticker to make it visible for the Trigger sensor.
Note
TITAN can detect Trigger position very precisely. In order to use it, you need to eliminate Trigger backlash. The set contains 3 Trigger anti-backlash stickers of various thicknesses. Try each one of them and choose the most appropriate one.
Note
The Selector plate requires modification. Place the Selector sticker according to the photos below. Its position is crucial.
Caution
In TITAN V3 the connectors must be straight according to the photo below. Bending and straightening the connectors back may cause them to break. If this should happen, spare terminals are included in the INSTALLATION KIT.
TITAN V2 NGRS
Warning
If you are using a recoil system and set excessive Trigger sensitivity, it may cause accidental discharge (firing) even without pressing the Trigger.
Warning
Pay attention to correctly solder positive and negative TITAN wires to the connector. Incorrectly connecting positive and negative battery terminals will cause immediate damage to the device, which is not covered by warranty, and can lead to fire.
Caution
An insulation washer is required. Placing washers in the wrong order will cause a short circuit and permanent damage to TITAN, which is not covered by warranty.
Caution
Do not locate the screw in the cut-off lever hole to secure the TITAN board. Use a contact block mounting screw in the hole indicated by the arrow.
Caution
Incorrect placement of wiring under the motor gear may cause insulation damage and a short circuit, which is not covered by warranty.
Caution
In order to secure the wires properly, modify the gearbox as shown in the photos below.
Note
The Selector plate requires modification. Place the Selector sticker according to the photos below. Its position is crucial.
Caution
In TITAN NGRS connectors should be bent according to the photo below. Bending connectors in the opposite direction may cause them to break. If this should happen, spare terminals are included in the INSTALLATION KIT.
Quick Access Menu
You can access Pre-cocking or Profiles using a shortcut. After firing a shot, burst or while in SAFE (only if the safety lever has been removed)*, hold the Trigger and switch the Selector within the specified time (see table). Switch the Selector in any order to change between options indicated by motor vibrations.
By releasing the Trigger, you exit the function confirming it. Bear in mind that programming via Trigger is a different process. To find out more check the PROGRAMMING VIA TRIGGER CARD included or https://gatee.eu/technical-support/manuals.
*You can enter Programming via Trigger only when the Selector on the replica is in SEMI position and AUTO mode is not assigned to this position.
Function | |||||
available if preset in GCS | in SEMI or BURST mode preset in GCS in SEMI physical position only | ||||
Pre-cocking | Profiles (EXPERT only) | Programming via Trigger | |||
To enter the function: hold the Trigger | and switch the Selector within 2 s | and switch the Selector within 2–7 s | for > 7 s | ||
Available options | Option | Low frequency vibration | Option | High frequency vibration | check the PROGRAMMING VIA TRIGGER CARD included or https://gatee.eu/technical-support/manuals |
Off | 1 | Profile 1 | 1 | ||
Auto | 2 | Profile 2 | 2 | ||
Manual* | 3 | Profile 3 | 3 | ||
*If defined in GCS
Pre-cocking Selection
In GCS go to Trigger>Pre-cocking>Switch mode via Selector and use the toggle button to activate this function.
Fire a shot, burst or pull the Trigger while in SAFE mode (only if the safety lever has been removed) and do not release the Trigger.
Switch the Selector within 2 s. There is a single low frequency vibration.
Switch the Selector in any order to change between options, which are indicated by vibrations:
1 low vibration – Pre-cocking Off
2 low vibrations – Pre-cocking Auto
3 low vibrations – Pre-cocking Manual
Release the Trigger to save the selected mode.
Profile Selection
Profiles are sets of particular settings of configurable TITAN functions. You can choose one of the three profiles at a time. Go to General>Profiles>Change profile change via Selector in GCS to be able to use this function. If you want to change the active Profile:
Fire a shot, burst or pull the Trigger while in SAFE (only if the safety lever has been removed) and do not release the Trigger.
Switch the Selector within 2–7 s. There is a single high frequency vibration.
Switch the Selector in any order to change between options, which are indicated by vibrations.
1 high vibration – Profile 1
2 high vibrations – Profile 2
3 high vibrations – Profile 3
Release the Trigger to save the selected profile.
Continue:
Information for Use (In4U) [TTN]
Go back to:
QuickStart Guide (QSG) [TTN]
Safety & Regulatory Information [TTN]