Page Information

    Page: Can I swap front and rear wiring in my ETU?
    Page: Is TITAN/ASTER compatible with KWA gearboxes?
    Page: What does the Equalizer do and how to set it?
    Page: What is ROF control?
    Page: Why does ROF control not lower the RPS in direct proportion to the value set in GCS?
    Page: What is the correct nozzle position once stationary?
    Page: Why are the wires and motor getting very hot on SEMI?
    Page: Why does my battery discharge very quickly?
    Page: Why must I use an insulation washer?
    Page: What is the maximum allowed Amperage for TITAN?
    Page: Why does my WARFET 1.1 have such a short range of Precocking adjustment?
    Page: Why does my replica overspin/fire two BBs at a time on SEMI?
    Page: ASTER won't fire
    Page: Does Quantum Trigger require a gearbox sticker?
    Page: I would like to set hair-trigger sensitivity on my ASTER V2, why can’t I do this?
    Page: KWA gearboxes compatibility with ASTER V2
    Page: Why does my trigger with travel adjustment stop working after a few shots?
    Page: Double shots on SEMI and the E07 DTC
    Page: How can I use 32:1 or slower gears in TITAN V2/V3?
    Page: Torn off or broken yellow capacitor in my TITAN V2
    Page: What do I do if my TITAN V2 doesn’t detect current sector gear position?
    Page: Why does the Tactical Programming Card keep blinking?
    Page: Why is one of my Titan trigger sensors shown as unavailable in GCS?
    Page: Which devices are compatible with Blu-Link?
    Page: Which devices are compatible with USB-Link?
    Page: Why doesn't my Android phone recognize USB-Link?
    Page: Why isn't my USB-Link visible in desktop GCS?
    Page: How to solder Deans-T connectors?
    Page: How to enter HPA mode.
    Page: Where can I find serial number of my ETU?
    Page: The difference between rear and front wiring
    Page: EON Gearbox Shell Revision 1 & 2
    Page: Does the PULSAR S HPA Engine engine come with male QD fitting?
    Page: Will the aftermarket IGL fit the PULSAR S HPA Engine?
    Page: Why is ROF Control locked?
    Page: How to fix a faulty spring guide?
    Page: ASTER V2 SE vs ASTER V2 SE LITE
    Page: TITAN II Bluetooth® Compatibility with HPA Engines
    Page: GATE & ICS Gearbox Compatibility
    Page: What are the dimensions of the air hose that connects to the HPA engine?
    Page: Will PULSAR S I ordered come with a hose connector, and if so, what kind (EU/US)?
    Page: Is PULSAR S HPA engine a closed or open bolt system?
    Page: What is the maximum pressure that can be set with PULSAR S engine?
    Page: The replica shoots in various directions.
    Page: There is no air coming out of the system and the nozzle stays back.
    Page: The first shot is a deadshot (when the replica requires pulling the trigger twice to shoot the BB out) in PULSAR S HPA engine.
    Page: Is PULSAR S compatible with the ICS CXP MARs (split gearbox)?
    Page: Which regulators will work best with PULSAR S?
    Page: Does PULSAR S work well with the Maxx Models pro chamber?
    Page: What's the difference between SHORT and FULL STROKE?
    Page: Do I need a battery if I'm using the PULSAR S HPA engine in my replica?
    Page: How to register to a lifetime guarantee for my EON Gearbox?
    Page: Is TITAN V2 NGRS compatible with V2 gearboxes?
    Page: PULSAR D Tappet Plate modification
    Page: PULSAR S NOZZLE Diameter Issue
    Page: Where's my PIN?
    Page: How to check the compatibility of the cylinder head with the EON Gearbox
    Page: How does the battery saving mode work in my TITAN II Bluetooth and ASTER II Bluetooth?
    Page: Which Hop-Up bucking should be used with the PULSAR H engine?
    Page: Which Hop-Up bucking should be used with the PULSAR D engine?
    Page: Which Hop-Up bucking should be used with the PULSAR S engine?

View Page History